Évaluations - , GPA: ( )

Instructions ACR Electronics, Modèle HydroFix 9490

Fabricant : ACR Electronics
Taille : 725.61 kb
Nom Fichier : 59f06985-b92a-47e9-a842-2f542b27e8f9.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Take great care to hold the spring in place during removal and installation of the new HRU to prevent injury. WARNING: Stow the EPIRB in a dry location as it will activate if out of the bracket and wet. WARNING: Non-ACR-supplied hydrostatic release units must not be installed in ACR Category I EPIRB brackets. ACR cannot and does not warrant the performance of other manufacturers’ products. Installation of a non-ACR-supplied HRU voids the warranty and potentially jeopardizes your safety. CAUTION: Visually check the EPIRB when removing it from the bracket. It must be sent back to ACR for check up and/or refurbishment if ANY of the following conditions exist: • Cracks to the exterior plastics • Activation indicator break tab is broken • Moisture appears inside the EPIRB • Lacquer is not present in one of the screws or appears to have been tampered with NOTE: Some parts in this kit will not be used. Refer to Figure 1 and the instructions for your specific model for details. Discard unused parts. \\Eng-sec\CR Public\HRU Graphics\HRU calendar for manuals.jpg SECTION 3 – HOW TO DETERMINE HRU EXPIRATION DATE The ACR HydroFix™ HRU is a replaceable part and, as such, has dating associated with it. The HRU must be replaced two (2) years from the install date or four (4) years from the date of manufacture, whichever is less. The HRU has a calendar on its top side; the calendar should be marked with the expiration date at the time of installation, according to the following instructions. Date of Installation Example: Date of installation of New HRU or first installation of EPIRB including new HRU: August 1, 2009. This unit will need to be replaced in August 2011. Mark off “AUG 8” and “2011” on the HRU date calendar Date of Manufacture Example: On the bottom of the HRU a date of manufacture is pin stamped: 0808. This unit will need to be replaced in August 2012. Mark off “AUG 8” and “2012” on the HRU date calendar Figure 2 SECTION 4 – INSTALLING THE HRU IN A SeaShelter3™ BRACKET The following ACR EPIRBs are compatible with the SeaShelter3™ (ACR P/N 9501): . GlobalFix™ iPRO, or models RLB-36 and higher Contents of the HydroFix™ HRU Kit that you will need: . HydroFix™ Replacement Hydrostatic Release Unit (E) . Large cotter pin (H) . HRU expiration label (K) . SeaShelter3™ release rod (M) Instructions: 1.) Remove the front cover of the bracket and carefully release the EPIRB from the bracket. 2.) Remove the old HRU unit and rod from the bracket by pressing the spring release back and rotating the old HRU out of the bracket. 3.) Take the SeaShelter3™ release rod (M) and place it on top of the rod on the HRU, aligning the two sets of holes on the base (see Figure A). 4.) Place large cotter pin (H) inside the two holes, securing the two rods together. 5.) Mark the expiry date on the HRU according to the instructions in Section 3. 6.) Record the expiration date on the HRU expiration label (K) with an indelible marker. 7.) Push the release spring back against the bracket aligning the holes on the spring with the holes on the back of the bracket. 8.) Take the assembled HRU and place the end of the HRU through the slot. 9.) Turn the HRU to the left side of the bracket (see Figure B). 10.) This will lock the HRU and spring into place. Carefully release the HRU and make sure it is securely in place. Figure A 11.) Reinstall the beacon with the lanyard facing toward the back of the bracket. 12.) Place the bracket top cover on top of the bottom cover. 13.) Make sure the bottom hinge and the top handle are securely connected. 14.) Place HRU expiration label (K) on the outside of your bracket in a visible location. Figure B SECTION 5 – INSTALLING THE HRU IN A SeaShelter2™ BRACKET The following ACR EPIRBs are compatible with the SeaShelter2™ (ACR P/N 9435/9455): . GlobalFix™ 406 . RapidFix™ 406 . SATELLITE2 406™ . SATELLITE 406™ (discontinued product) Contents of the HydroFix™ HRU Kit that you will need: . HydroFix™ Replacement Hydrostatic Release Unit (E) . SeaShelter™ release rod (A) . Keyed bracket adapter (D) . Large cotter pin (H) . HRU expiration label (K) Instructions: 1.) Remove the front cover of the bracket and carefully release the EPIRB from the bracket. 2.) Remove the old HRU unit and rod from the bracket by pressing the spring release back and sliding the old HRU up and out of the bracket. 3.) Take the SeaShelter2™ release rod (A) and place it on top of the rod on the HRU, aligning the two sets of holes on the base (see Figure A). 4.) Place large cotter pin (H) inside the two holes, securing the two rods together. 5.) Place keyed bracket adapter (D) on the bottom of the HRU. This part is keyed so that it will fit together only one way. Turn to the right until it snaps into place. 6.) Mark the expiry date on the HRU according to the instructions in Section 3. 7.) Record the expiration date on the HRU expiration label (K) with an indelible marker. Figure A 8.) Push the release spring back against the bracket aligning the holes...