Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Press the OK key and then the Teletext OSD you want is displayed on the screen. 10. Teletext VBI When the current broadcasting program provides Teletext VBI, press the GREEN(TEXT) key three times to see the current language list for Teletext. This Teletext will be displayed to the screen by TV, which supports Teletext. [T] at the right corner on the banner shows that Teletext is available on this event(program). Even [T] is displayed on the banner, Teletext may not be available due to broadcasting To change the Teletext VBI: . Use the / keys to select a Teletext VBI you want. . Press the OK key and then the Teletext VBI you want is displayed on the screen. 11. Audio Mode You can choose a mode among left, right or stereo using the BLUE(AUDIO) key. To change the audio mode: . Press the BLUE(AUDIO) key to select the left, right or stereo. . Press the EXIT key to save and escape from this menu. 12. Near Video on Demand (NVOD) If the changed channel is a NVOD [N] is displayed at the right corner on the banner. In this case, press the YELLOW(ALT) key. Then you can get all NVOD list. Select NVOD program among those lists. Select the desired time to watch using the / keys, and then press the OK key to watch the desired program. 13. Multi feed channel or subchannel If the changed channel is a multi feed service channel, [C] is displayed at the right corner on the banner. In this case, press the YELLOW(ALT) key. Then you can get all subchannel list. Select a program among those list, using the / keys, and then press the OK key to watch the selected program. DIGITAL SATELLITE RECEIVER GB-14 GB-15 OPERATING THE RECEIVER OPERATING THE DSB-A100F GB DSB-A100F Main Menu After installing your antenna system connectors. . Plug in the AC main power and switch . Press MENU key to bring up the main menu. The LED display will show “ MENU” . The following on screen display will appear: The sub menu topics will be displayed. For the sub-menus Installation, Channel Organising and Parental Lock you need the PIN Code. Before you begin with the “Installation” menu, you should check in the 4th menu “System Setup” whether all the information there is applicable for you. . To see the help message, press the YELLOW(ALT) key. 1. Installation The menu provides settings for customizing, adding new services and displaying the status of the receiver. . Select “ Installation” in the main menu mode to select the sub menu. . Enter the PIN Code. If you have not entered your own PIN Code then the PIN Code 0000 applies, which was set at the factory. 1.1 LNB Setting You can select the satellite and LNB setting conditions to execute channel search and you can alter the settings for 22KHz tone. The parameters set in this needed for programming the channels for the “ Auto scanning” and “ Manual scanning”. The necessary information can be found at your LNB brochures, or you can ask your dealer. . Select LNB power supply “ On”. . Select the desired satellite name. . Select the LNB type (frequency). . Select the DiSEqC Mode (Off, DiSEqC A, DiSEqC B, DiSEqC C, DiSEqC D, Tone Burst A, Tone Burst B) If you are using a Positioner, select Positioner DiSEqC1.2 (“ Yes” or “ No”) 22KHz: In case you are using a dual LNB or two antennas connected to a 22KHz tone switch box, with the 22 KHz tone switch (“ On”, “ Off” or “ Auto”) you can switch between both LNB or antennas. 1.2 Positioner Setting If you have a DiSEqC 1.2 motorized system which is fully compatible with DiSEqC1.2, then you can take advantage of the DiSEqC 1.2 functions available. . Select Satellite. . Select any transponder from above satellites and check out the Frequency, Symbol Rate, FEC and Polarity. In case problems arise, ask your dealer. Sometimes this transponder may not exist due to broadcasting. It is better to select main transponder among them for the desired satellite. . Select from Menu Mode: “ User” mode : Enables control of basic positioner function recommended for beginners. General user uses “ User” mode. “ Installer” mode : This is used to search for the position of a satellite manually. DIGITAL SATELLITE RECEIVER GB-16 GB-17 OPERATING THE RECEIVER OPERATING THE RECEIVER DSB-A100F GB DSB-A100F 1.2.1 User Mode . Select Driving Mode: You have an option to choose the positioner’s movement type: Continuous, Step or Time. . Position the antenna with north, south, east use the / / / key to drive motor. key drives to west, key drives to east, key drives to north and key drives to south. . If you finished driving of motor, select “ Store current Position. ” and press OK key, to reset new driving motor. Note : The level indicated in the “Signal Status” is only for reference. The signal quality may be adequate even though the level indicated . Go to Stored Position. When the stored position is reached then screen displays “ Stop”, you can now continue with the further operations. . Select the Calculate Sat Positions to recalculate the satellite position and OK key. 1.2.2 Installer...