Fabricant : Marmitek
Taille : 886.67 kb
Nom Fichier :
|
Facilité d'utilisation
[10] AV 3 To select an external source (SCART input). [11] ENT For some devices, this button in 5 combination with the numeric keys allows you to directly select channels 4 higher than 9. If you are in programming 6 mode - automatic code search - you can 7 8 use it to confirm the code. [12] Menu Menu ON [13] Exit Menu OFF [14] OK To confirm menu selection. 9 Up, Down, Right, Left. These allow you to navigate through the menu (TV, DVD, etc.). [15] Navigation keys [16] 10 Teletext Hold: Stop page change in eletext/Fasttext mode. Teletext ON: Start/stop eletext/Fasttext. Teletext OFF: Stop Teletext/Fasttext. 11 13 Teletext Mix: Allows you to mix the 12 Teletext/Fasttext and the picture of the 15 selected channel. 14 [17] REW (rewind) 16 In VCR or DVD mode: This button works the same way as the one on your original remote control. IN TV mode: Coloured key (Red), videotext 17 18 control or special equipment functions. 19 20 [18] FF (fast forward) 21 22 In VCR or DVD mode: This button works the same way as the one on your original remote control. IN TV mode: Coloured key (Red), videotext control or special equipment functions. TV ANYWHERE [19] PLAY In VCR or DVD mode: This button works the same way as the one on your original remote control. IN TV mode: Coloured key (Yellow), fasttext control or special equipment functions. [20] STOP In VCR or DVD mode: This button works the same way as the one on your original remote control. IN TV mode: Coloured key (Green), fasttext control or special equipment functions. [21] REC (record) This key works the same way as the one on your original remote control for your VCR. In order to avoid mistakes, you have to press this key twice to activate this feature. [22] PAUSE In VCR or DVD mode: This button works the same way as the one on your original remote control. IN TV mode: Coloured key (purple), fasttext control or special equipment functions. 7.3. Setting the remote control for your TV, VCR, DVD player and satellite receiver To make your remote control suitable for your own equipment, you have to program it once. You can do this by entering a code, related to the brand and type of equipment you want to control. You can program any device under any MODE button. For example, if you have two VCRs, you can program VCR 1 under VCR and VCR 2 under DVD. 7.3.1 Manual code entry Take your code book and search for the list matching the device you are looking for, e.g. TV or VCR. Next, find the relevant brand (e.g. Sony). Now you will see one or more 3-digit codes. If there is more than one code, it depends on your equipment which code is correct. Generally, the codes are displayed in order of age of the device. Older devices first, newer devices last. Sometimes you will have to try several codes before you find the right code for your device. 1. Make sure your device is switched on (for example the TV). 2. Press and hold SETUP [7] until the LED indicator stays lit. Release SETUP . 3. Press and release the mode button [3] of the device you want to control (for example TV). 4. Enter the 3-digit code from the code book by using the key pad [9]. The LED [2] will extinguish after the last digit is entered. If you have entered a wrong code, the LED will flash for 3 seconds and then extinguish. You have to repeat steps 2-4. 5. Point the remote at your TV and press the POWER button [1]. Your device should now turn off. Check other functions (for example for a VCR FF or REW, etc.). If certain functions are not responding, the entered code is not the correct one. In that case repeat the steps above with the next corresponding code of your brand. 6. Repeat this procedure from step 1 for the other devices you want to control (VCR, DVD, SAT,...). MARMITEK 7.3.2 Automatic code search for some well-known brands If your brand is listed below, you can use the brand search method (faster than the "manual" and the "automatic code search"). BRAND CODE Philips/Radiola/Aristona/Erres 1 Sony/Panasonic/JVC/Sharp/Akai/Toshiba/Daewoo 2 Thomson/Brandt 3 Telefunken/Saba/Nordmende 4 Grundig/Blaupunkt 5 Nokia/ITT 6 1. Turn on the device you want to control. 2. Press and hold SETUP [7] until the LED indicator [2] stays lit. Release SETUP. 3. Press the mode button (3) that matches the device you wish to control. The LED [2] will flash once. 4. Enter the code for your brand, point the TV Anywhere Remote at your device and press Prog+ [5] once. Continue to point the TV Anywhere remote control at your equipment until the equipment changes Channel. (The remote control transmits an IR signal every second. Please wait until your device reacts) When your device does react, press ENT [11] to confirm. If you accidentally go past the code, you can stop the autosearch by pressing Prog- [5] and by repeatedly pressing this button return to the right code. Press ENT [11] to confirm. • If some functions of your device do not work, you need to try another code for your brand. The search function starts after the last confirmed code...
Ce manuel est également adapté pour les modèles :Récepteurs Satellite - 20095 (886.67 kb)