Évaluations - 4, GPA: 3.8 ( )

Fabricant : Samsung Taille : 3.84 mb Nom Fichier : Langue d'enseignement:

After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual). Selecting the Video Signal-source Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system). 1 Press MENU to display the menu. Press CH two times to select “Channel”, then press the VOL + button. 2 Repeatedly press VOL + to cycle through these choices: ANT (antenna) STD, HRC or IRC (all cable TV). Note: STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (next page). 3 Press MENU twice to exit. -VOL+ MECH OPERATION Storing Channels in Memory (Automatic Method) 1 First, select the correct signal source (ANT, STD, HRC, IRC). See steps 1~3 on previous page. Press the MENU button, then press the CH button twice to select “Channel,” then press the VOL + button. 2 Press the CH button to select “Auto program”. 3 Press the VOL + button. The TV will begin memorizing all of the available channels. 4 After all the available channels are stored, the Auto program menu reappears. Press the MENU button twice to exit. -VOL+ CH MENU Ў The TV automatically cycles through all of the available channels and stores them in memory. This takes about one to two minutes. Press the MENU button at any time to interrupt the memorization process and return to the Channel menu. OPERATION Adding and Erasing Channels (Manual Method) Press the MENU button. Press the CH button twice to select "Channel", then press the VOL+ button. 2 Press the CH or CH Ў button to select “Add/Erase”. Press the VOL+ button. 3 Press the VOL-/+ or number buttons to select the channel you want to add or erase. 4 Press the CH or CH button to select “Select”. Press the VOL+ or VOL- button to select “Added” or “Erased”. Press the MENU button three times to exit. OPERATION Changing Channels Using the Channel Buttons 1 Press the CH or CH button to change channels. When you press CH or CH , the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels.) You will not see channels that were either erased or not memorized. Directly Accessing Channels Use the number buttons to quickly tune to any channel. 1 Press the number buttons to go directly to a channel. For example, to select channel 27, press “2,” then “7.” The TV will change channels when you press the second number. When you use the number buttons, you can directly select channels that were either erased or not memorized. To select a channel over 100, press the +100 button. (For channel 122, press “+100,” then “2,” then “2.”) To change to single-digit channels (0–9) faster, press “0” before the single digit. (For channel “4,” press “0,” then “4.”) Using the PRE-CH Button to select the Previous Channel Ў To quickly switch between two 1 channels that are far apart, tune to Press the PRE-CH button. one channel, then use the number The TV will switch to the last channel viewed. button to select the second channel. Then, use the PRE-CH button to quickly alternate between them. Adjusting the Volume Press the VOL + or VOL– button to increase or decrease the volume. Using Mute At any time, you can temporarily cut off the sound using the Mute button. 1 Press the MUTE button and the sound cuts off. The word “Mute” will appear in the lower-left corner of the screen. 2 To turn mute off, press the MUTE button again, or simply press either the VOL – or VOL + button. OPERATION Setting the Clock 1 Press the MENU button to display the on-screen menu. Press the CH button three times to select "Function". Press the VOL + button. 2 Press the CH button to select the “Time” menu. Press the VOL + button: The Time menu will appear on the screen, and “Clock” will be selected. When selecting the hours, be sure 3 to select the proper time of day (AM Press the VOL + button or PM). again (the hours digits will be selected). Press the CH or CH button repeat- You can change the hours by pressing CH or CH repeatedly (or by edly until the correct hour appears. holding down either of these buttons). After the hour is entered, press the VOL + button. (at this point the minutes digits will be selected). The time will appear every time 4 you press DISPLAY. Press the CH or CH Ў button to select the correct minutes. After selecting the correct minutes, press the VOL + button. Press the MENU button three times to exit. 25 OPERATION Customizing the Picture You can use the on-screen menus to change the contr...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :