Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
Ignoring this warning can lead to a severe crushing injury or finger amputation! Specifications • Fits Lathe Models ..14" x 40" SB1012, SB1013 ................................16" x 60" SB1014, SB1015 ............................... 16" x 40" SB1037, SB1038 • Taper Per Inch Range.............................0–18" • Minor Inch Scale Divisions....................0.010" • Major Inch Scale Divisions....................0.020" • Taper Angle Range .................................0–10° • Minor Taper Scale Divisions .......................1.2° • Major Taper Scale Divisions.........................1° • Maximum Length of Taper..................... 121.4" • Taper Adjustment Knob............................Yes • Construction.............................................Steel • Unit Weight............................................78 lbs • Origin................................................... Taiwan Introduction The Model SB1269 taper attachment was designed to fit onto a series of South Bend lathes. Shown in Figure 1, is a Model SB1012 lathe that is fitted with the Model SB1269 taper attachment. Taper attachment installed on rear side of lathe Figure 1. Model SB1269 installed. This taper attachment mounts quickly to the back bed way of your lathe. Accurate tapers of up to 12" can be produced without repositioning the attachment or having to offset the talstock. The Model SB1269 features scales at both ends, reading inches-per-foot and degrees. An angle adjusting knob with fine threads achieves exacting control when setting tapers. Another feature is the ability to use the taper attachment without disengaging the cross slide nut. This design allows the taper attachment to be functional at any time by simply tightening the two deadman-clamp cap screws, which lock the deadman-clamp to the rear lathe way. If you need help with your new item, contact us at: (360) 734-1540 • FAX: (360) 676-1075 Identification Serious personal injury could occur if you connect the lathe to power before completing the installation process. DO NOT connect power until instructed to do so later in this manual. Untrained users have an increased risk of seriously injuring themselves with this lathe accessory. Do not operate lathe until you have understood this entire manual and received proper training. Dead Man Arm Taper Knob Taper ScaleDead Man Clamp Travel Stop Dovetail Gib Gib Adjustment Screws Main Housing Table Way Arm Clevis Figure 2. Identification. -2For Product Mfg. Since 1/10 Model SB1269 INTRODUCTION Serious personal injury could occur if you connect the lathe to power before completing the installation process. DO NOT connect power until instructed to do so later in this manual. Untrained users have an increased risk of seriously injuring themselves with this lathe accessory. Do not operate lathe until you have understood this entire manual and received proper training. Dead Man Arm Taper Knob Taper ScaleDead Man Clamp Travel Stop Dovetail Gib Gib Adjustment Screws Main Housing Table Way Arm Clevis Figure 2. Identification. -2For Product Mfg. Since 1/10 Model SB1269 INTRODUCTION For Product Mfg. Since 1/10 PREPARATION Model SB1269 Unpacking This item was carefully packaged to prevent damage during transport. If you discover any damage, please immediately call Customer Service at (360) 734-1540 for advice. You may need to file a freight claim, so save the containers and all packing materials for possible inspection by the carrier or its agent. Inventory When you are completely satisfied with the condition of your shipment, you should inventory the contents. Inventory (Figure 3) Qty A. Cap Screws M10-1.5 x 40mm (Taper Attachment Mounting)......................4 B. Taper Attachment Assembly.........................1 C. Tapered Pins 8.7 x 7.7 x 47mm.....................2 D. Copper Anti-Score Plug .................................1 E. Deadman Clamp Assembly ...........................1 F. Deadman Arm and Clevis .............................1 Things You'll Need This attachment is intended to be a permanent installation. Installation will take approximately 1.2 hours and require the following items: For Assembly • Cotton Rags • Mineral Spirits • Safety Glasses • Oil Can with any Basic Machine Oil • Assistant • Open End Wrench (17mm) • Hex Wrenches (3, 4, 5, 6, and 8mm) • Tapered Drill Bit (8mm) • Safety Glasses • Oil Can with Pressure Tip • Dila Indicator with Magnetic Base • Phillips Screwdriver, #2 • Hammer • Drill Bit, 19.64" • Spiral Pin Reamer, Industrial Size: 6 —Small End Diameter: 0.2773" —Large End Diameter: 0.3540" A B C DE F Figure 3. Model SB1269 inventory. -3 The unpainted surfaces are coated with a heavy- duty rust preventative that prevents corrosion during shipment and storage. This rust preventative has been a close ally and guardian since this item left the factory. If the unpainted surfaces are free of rust, then be thankful that the rust preventative did its job...and try to stay thankful as you clean it off, because it...