Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
. The drying time or degree of drying has not been selected . The water tap is not turned on (E EE1 110 00) . The drain filter is clogged (E EE2 220 00) . The machine is overloaded . The selected drying time or degree of dryness was not suitable for the laundry. Service & Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact our extended warranty administrators by telephoning: 0870 01 07887 They will give you details for your local Service Force Centre. Before calling out an engineer, please ensure you have read the details under the heading “Something Not Working”. When you contact the Service Centre you will need to give the following details: 1. Your name, address and post code 2. Your telephone number 3. Clear and concise details of fault 4. The model and serial number of the appliance (found on the rating plate - see picture) 5. The purchase date. Please note that a valid purchase receipt is required for in-guarantee service calls. 23 Installation Instructions It is dangerous to alter the specifications or attempt to modify this product in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. Technical Specifications DIMENSIONS Height Width Depth 85 cm 60 cm 59 cm POWER SUPPLY VOLTAGE TOTAL POWER ABSORBED 230-240 V/50 Hz 2050 W (10 A) WATER PRESSURE Minimum Maximum 0.05 MPa (0.5 bar) 0.8 MPa (8 bar) MAXIMUM RECOMMENDED LOAD Washing Cotton, linen Synthetics Duvet/Delicate fabrics Wool/Hand wash Drying Cotton, linen Synthetics 6 kg 3 kg 3 kg 2 kg 3 kg 2 kg SPIN SPEED Maximum 1400 rpm CONSUMPTION DATA FOR WASHING 6 KG NORMALLY SOILED COTTON ITEMS WITH PROGRAMME “COTTONS 60°” (White and Coloured Cottons): Energy Water 1.19 kWh 52 litres This appliance complies with the following E.E.C. Directives: - 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications. 24 Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all the packaging for re-use in case the machine is to be transported again. Using a spanner unscrew and remove the two rear bottom screws. Slide out the two plastic pins. Lay the machine gently on its back, making sure that the hoses are not squashed. Remove the polystyrene block from the bottom of the machine and release the two plastic bags. Very carefully slide out the left polythene bag, removing it towards the right and then downwards. Repeat the operation for the right polythene bag, removing it towards the left and then upwards. Remove the polystyrene base. Set the machine upright and unscrew the remaining rear screw. Slide out the relevant pin. Fill all the holes with the plastic plugs supplied with the instruction booklet. Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. Your new washer-dryer has been designed to be permanently plumbed in to your home’s water supply and drainage system. However, if this is not possible, it may be connected to a suitable existing tap with the drain hose discharging into a sink. The appliance has an inlet hose, with female 3/4” BSP thread connector. If this connection is not compatible with the plumbing of the existing installation, a variety of connectors are available from good hardware stores and plumbers merchants to suit most domestic plumbing. Any alteration to your existing plumbing must be carried out by a competent person, or qualified plumber. Installation on a Suspended Floor Suspended wooden floors are particularly susceptible to vibration. To help prevent vibration we recommend you place a waterproof wood panel, at least 15 mm thick under the appliance, secured to at least 2 floor beams with screws. If possible install the appliance in one of the corners of the room, where the floor is more stable. 25 Water inlet Connect the hose to a tap with a 3/4” thread. Always use the hose supplied with the appliance to connect to the water supply. Do not use previously used hoses for water connection. Installation should comply with local water authority and building regulations’ requirements. The appliance must be connected to a cold water supply. A minimum water pressure of 0.05 MPa (0.5 bar) is required for safe operation of the appliance. If you cannot make the cold water connection direct from the rising mains, you m...