Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
If washer or dryer is new and has not been installed yet, skip to step 4. 2. If dryer is already installed, disconnect dryer from electrical and gas connections and exhaust venting. 3. If washer is already installed, disconnect washer from electrical connection. Turn off hot and cold water supply and disconnect hot and cold water supply hoses from water supply outlets. Disconnect drain hose from drain pipe. 4. If appliance has plastic feet, screw each foot fl ush to the base. 5. If appliance has metal feet, unscrew them, remove the locking nut and reinstall the feet fl ush to the base. A) Preparing washer or dryer for mounting on pedestal B) Preparing pedestal before mounting washer or dryer 1. Locate pedestal to within a few inches of its fi nal location. 2. Level the pedestal front-to-back and side-to-side by adjusting each leveling leg. Keep leg extension to a minimum. 3. Rock the pedestal from corner-to-corner to check for stability. Repeat leveling and rocking until all four (4) feet are sturdy on the fl oor and pedestal is level. 4. Without turning the rubber foot, lock each pedestal leg in place by tightening its lock nut tight against the pedestal base. DO NOT remove foam! lock nut raise lower Optional universal wrench (or adjustable pliers). 3 - EXCESSIVE WEIGHT HAZARD - To avoid back or other injury, have more than one person move or lift the washer. C1) Attaching washer mounting hardware 3.5 cu ft WASHER INSTRUCTIONS (GREEN KIT) D1) Mounting washer E1) Installing or re-installing washer 1. Use the following instructions for mounting either of these types of washers to the pedestal: 1. Using two or more persons, slightly tip the washer back and lift it onto the pedestal. Still tipped, slide the washer back against the rear brackets and gently set down the front so the appliance is between the front and rear brackets. 2. Attach each front clip to outer-most set of holes with 2 screws and supplied spacer. 3. Insert “A” tab of each rear bracket into the middle slots on rear of pedestal. Orient bracket inward for washer mounting. 2. Adjust the appliance side-to-side to align its mounting holes with the pedestal’s bracket holes. 3. Install 2 screws through each rear bracket into the base of the washer. 4. Install a screw through each front bracket into the base of the washer. 1. Slide appliance/pedestal into place. 2. Check for levelness and rock all four (4) legs again. Repeat until level and solid. 3. Refer to Washer Installation Instructions for complete details on installing water, drain, or electrical. SLIDE BACK TIP DOWN middle slot inward 4. Install 2 screws through each rear bracket into aligning pedestal holes. Locate spacer under each front bracket. “A” tab • GREEN KIT • GREEN KIT • GREEN KIT • GREEN KIT • GREEN KIT • 4 C2) Attaching dryer (style 1) mounting hardware D2) Mounting dryer (style 1) E2) Installing or re-installing dryer (style 1) 1. Use the following instructions for mounting any of these types of dryers to the pedestal: 1. Using two or more persons, slightly tip the dryer back and lift it onto the pedestal. Still tipped, slide the dryer back against the rear brackets and gently set down the front so the appliance is between the front and rear brackets. 2. Attach each front clip to outer-most set of holes with 2 screws. 3. Insert “A” tab of each rear bracket into the rear slots on rear of pedestal using rear bracket spacers. Orient bracket inward for “style 1” dryer mounting. 2. Adjust the appliance side-to-side to align its mounting holes with the pedestal’s bracket holes. 3. Install 2 screws through each rear bracket into the base of the dryer. 4. Install a screw through each front bracket into the base of the dryer. 1. Slide appliance/pedestal into place. 2. Check for levelness and rock all four (4) legs again. Repeat until level and solid. 3. Refer to Dryer Installation Instructions for complete details on installing electrical, gas, or exhaust venting. “A” tab rear slot inward 4. Install 2 screws through each rear bracket into aligning pedestal holes. Dryer cabinet (style 1) with 3 indents on side. 7.0 cu ft DRYER (STYLE 1) INSTRUCTIONS (GREEN KIT) NO spacers under front brackets. - EXCESSIVE WEIGHT HAZARD - To avoid back or other injury, have more than one person move or lift the dryer. SLIDE BACK TIP DOWN • GREEN KIT • GREEN KIT • GREEN KIT • GREEN KIT • GREEN KIT • 5 C3) Attaching dryer (style 2) mounting hardware D3) Mounting dryer (style 2) E3) Installing or re-installing dryer (style 2) 1. Use the following instructions for mounting any of these types of dryers to the pedestal: 1. Using two or more persons, slightly tip the dryer back and lift it onto the pedestal. Still tipped, slide the dryer back against the rear brackets so tabs on rear brackets engage the slots on the back of the dryer. Gently set down the front so the appliance is between the front and rear brackets. 2. Attach each front clip to outer-most set of holes with 2 screws. 3. Insert “B” tab of each rea...
Ce manuel est également adapté pour les modèles :Rondelles - 137147600 B (0906) (2.93 mb)