Évaluations - 1, GPA: 4
(
)
)
|
Facilité d'utilisation
The machine makes a noise or vibrates too much during the spin cycle. The machine leaks: Not all the detergent has been flushed out of the dispenser drawer. The dispenser drawer will not close properly or is collecting water. . Check that the detergent you have used is suitable for ‘Automatic’ machines. . Refer to the detergent manufacturers recommendations to ensure that you have not used too much detergent. . If you have used the wrong type of detergent (or too much), select a Rinse programme to flush out your machine. . This is not a fault, we have designed the machine to release steam from the drawers during hot washes. It may also vent during drying. . The transit fixings were not removed correctly (see Installation ‘Remove the transit fixings’) -Failure to remove all the parts of the transit fixings will cause the machine to vibrate excessively during spin. Note: There are TWO transit fixings that need to be removed - two bolts, two washers,two rubber grommets and two nylon spacers. . The machine is not level (see Installation) -Adjust the feet so that the machine stands firm on the floor (ie, it does not rock) and ensure the machine is level from front to back and from side to side. . The machine is closed in, between furniture cabinets and the wall (see Installation). . Perhaps the machine was attempting to spin an unbalanced load -Try the machine again with a different wash load. . When you sort your laundry into wash groups, check all loose items, such as coins are removed from the laundry. Check the drum at the end of each cycle and remove any loose items (coins etc). Note: ‘Super Silent’ refers to wash sound level only - there will always be some motor and drum noise during spin. ... from behind or underneath: . Check each end of both cold water inlet hoses, ensuring connections at both ends are tight and not leaking (see Installation). . Check all connections on the ‘Y’ piece connector - to ensure they are tight and not leaking (see Installation). . Depending on the installation method used (see Installation). Check that: -the drain hose is firmly secured to the undersink ‘U’ trap, or... -the drain hose is positioned correctly into the standpipe. . Check that your water pressure is within limits (see Technical Details Chart). -If too high, try turning the cold water supply tap down slightly and try the machine again (see Installation). ... from the dispenser drawer (water leaking down the front of the machine): . Check that the detergent dispenser is not blocked or obstructed. -Remove the drawer from the machine and clean it (see Care and Maintenance). . Check the cold water supply tap is turned on sufficiently (see Installation). . Is your water pressure is within limits (see Technical Details Chart), ifit is too low it may not be sufficient to flush all the detergent out of the drawer. . Check that the detergent dispenser is not blocked or obstructed. -Remove the drawer from the machine and clean it (see Care and Maintenance). . Is your water pressure too low? (see Technical Details Chart). Note: Are you using detergent tablets? - If yes, please check the detergent manufacturersinstructions on the side of the detergent box, not all detergent tablets are suitable for useinthe dispenser drawer some need to be placed into the machine drum with the wash load for them to dissolve correctly. . Check that the detergent dispenser is not blocked or obstructed. -Remove the drawer from the machine and clean it (see Care and Maintenance). 22 Something Wrong? - Troubleshooting Section 2: All Ultima Models - Problems with the Drying cycle? GB The laundry is not dry after using the drying programme. The load is warm at the end of the drying cycle. The machine spins during the drying cycle. The ‘Time to End’ changes Your machine uses cold water to condense the moisture extracted from the load. Check that: . Both of the cold water inlet hoses are connected to the cold water supply tap, using the ‘Y’ piece connector. . The inlet hoses are not kinked. . The cold water supply tap is turned on. Different load types need different heat settings. Some need HIGH heat, some need LOW heat. To prevent damage to your laundry, the machine default is LOWheat... If you are drying material such as Cottons for example check to ensure that you have selected HIGH heat, check that: -Before starting the programme press the Drying Heat option button, the display will show High Heat. Different load types need different drying times. . Timed Drying: Check that the drying time selected was sufficient for the load. . Sensor Drying: Ensure that you have selected the most appropriate drying setting for the load (see Drying). Note: Your machine contains an out of balance spin protection device, if the out of balance is too great the machine automatically spins at a lower speed. Check that the load was spun correctly at the and of the wash cycle before the machine advanced into the drying cycle, then try another rinse and spin and repeat...