Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
If the washer is installed on a carpeted floor, check that there is sufficient ventilation space between the floor and the bottom of the machine. Water supply Make sure that the water pressure is between the maximum and minimum values indicated on the data plate located on the back of the washer. Connect the inlet hose to a cold water tap with a 3/4 gas threaded opening, and fit the filter and the rubber gasket supplied with the washer. Check that it is tightly screwed to the tap (see fig. 5). If the water piping is new or has not been udes for a long time, before making the connection, let the water run until it is clear and free from impurities. This step is necessary to ensure that the incoming water does not clog and possibly damage the washer. Connect the other end of the pipe to the appliance, at the top on the right, by the water connection (see fig. 6). A Fig. 5 Fig. 6 Connecting the drain pipe Connect the drain hose to a drain (with a minimum inner diameter of 4 cm), avoiding excessive crimping or the formation of elbows. It is important that the hose be positioned at a height greater than 60 cm. If this is not the case, the hose must be fastened to the hook located on the top part of the back of the machine (fig. 7). If a drain pipe coming from the wall is used to connect the hose, have a qualified plumber/technician check to make sure that it functions properly. If your home is on the top of an apartment building or condominium, the drain may be subject to a siphoning effect which results in the machine filling and draining continuously. To eliminate this inconvenience, special valves are available on the market which can be fitted to the drain hose. Fig. 7 Electrical connection Before connecting the appliance to the mains, check the following: 1) your mains socket must support then maximum power load of the appliance, which is shown on the data plate; in addition the socket must comply with legal regulations; 2) the supply voltage must correspond to the values shown on the data plate; 3) the socket must be suitable for the plug of the appliance; replace the socket or the plug but do not use an adapter; 4) home electrical systems must be earthed, in compliance with ministerial directives. Should the electric system of your home not comply with these directives, the manufacturer declines any liability for any possible consequences. 21 GB Mounting the wooden panel onto the door Door Mounting Accessories (Fig. 8-9-10-11-12-13) and inserting the machine into cabinets: In the case where the machine must be shipped for final installation after the wooden panel has been mounted, we suggest leaving it in its original packaging. The packaging was designed to make it possible to mount the wooden panel onto the machine without removing it completely (see figures below). The wooden panel that covers the face of the machine must not be less than 18 mm in thickness and can be hinged on either the right or left. For the sake of practicality when using the machine, we recommend that the panel be hinged on the Fig. 8 Fig. 9 same side as the door for the machine itself - the left. N° 2 Hinge Supports N° 2 Hinges 1 2 3 4 5 6 lavabiancheriawashing machinemachine a laverwaschmaschine Lato portaDoor side Cote porte Tur seite A C E Fig. 10 Fig. 11 B N° 1 Rubber plug N° 2 Base molding guide Fig. 12 Fig. 13 No. 6 type A self-threading screws, l =13 mm No. 2 type F self-threading screws, l =9 mm No. 2 type B metric, countersunk screws, l =25; for fastening the magnet plate to the cabinet D No. 4 type C metric screws, l =15 mm; for mounting the hinge supports to the cabinet No. 4 type D metric screws, l =7 mm; for mounting the hinges on the supports 2 3 4 5 6 lavabiancheria washing machine machine a laverwaschmaschine Lato portaDoor sideCote porter e F Mounting the Parts onto the Face of the Machine · Mount the hinge supports onto the face of the machine, positioning the hole indicated by the arrow in Fig. 8 towards the inside of the face and using the type C screws. · Mount the magnetic plate on the opposite side, at the top, using the two type B screws. N° 1 Magnet N° 1 Magnet plate GB 22 Using the Drilling Template · Place the top edge of the drilling template so that it is flush with the top edge of the panel, making sure that it is positioned correctly and centered in the horizontal direction (use the dotted lines on the edges to line the template up). Mark the points on the panel for the four holes. · Use an appropriately sized router to mill the holes for the two hinges, the rubber plug and the magnet. Mounding the Parts onto the Wooden Panel (Door) · Insert the hinges into the holes (the movable part of the hinge must be positioned facing away from the panel) and fasten them with the 4 type A screws. · Insert the magnet into the top hole on the opposite side of the hinges and fasten it with the two type B screws. · Insert the rubber plug into the bottom hole. The panel is now ready to be mounted onto the machine. M...
Ce manuel est également adapté pour les modèles :Rondelles - LB6T (250.97 kb)