Overview of the washing machine Cover top Base cover Adjustable feet Debris filter Door Detergent drawer Control panel Bolt hole covers Plug Cold Water supply hose Drain Hose Selecting a location Before you install the washing machine, select a location with the following characteristics: • A hard, level surface (if the surface is uneven, see "Adjusting the leveling feet," below) • Away from direct sunlight. • Adequate ventilation • Room temperature that will not fall below 0 °C • Away from sources of heat such as coal or gas Make sure that the washing machine does not stand on its power cord. Ventilation openings must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. Adjusting the leveling feet If the floor is uneven, adjust the feet (do not insert pieces of wood or any other objects under the feet): 1. Loosen the leg bolt by turning it with your hand until it is at the desired height. 2. Tighten the locking nut by turning it with the wrench. • Place the washer on a sturdy, flat surface. If the washer is placed on an uneven or weak surface, noise or vibration occurs. (Only a 1 degrees angle is allowed.) 3 Installing the Washing Machine Removing the shipping bolts remove the bolts: Before using the washing machine, you must remove all of the shipping bolts from the back of the unit. To 1. Loosen all bolts with the wrench before removing them. 2. Take each bolt head and pull it through the wide part of the hole. Repeat for each bolt. 3. Fill the holes with the supplied plastic covers. 4. Keep the shipping bolts for future use. Connecting the water supply hose The water supply hose must be connected to the washing machine at one end and to the water faucet at the other. Do not stretch the water supply hose. If the hose is too short and you do not wish to move the water faucet, replace the hose with a longer, high pressure hose. To connect the water supply hose: 1. Take the L-shaped arm fitting for the cold water supply hose and connect to the cold water supply intake on the back of the machine. Tighten by hand. 2. Connect the other end of the cold water supply hose to your sink's cold water faucet and tighten it by hand. If necessary, you can reposition the water supply hose at the washing machine end by loosening the fitting, rotating the hose, and retightening the fitting. Positioning the drain hose The end of the drain hose may be positioned in three ways: Over the edge of a sink The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving. ln a sink drain pipe branch The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60 cm above the ground. ln a drain pipe Samsung recommends that you use a 65 cm high vertical pipe; it must be no shorter than 60 cm and no longer than 90 cm. 4 Washing a Load of Laundry Overview of the control panel 1. Detergent dispenser 2. Display panel Displays wash cycle and error messages. During execution of the program, the program indicator blinks. 3. Program Select button Press the button repeatedly to select one of the six available wash program. Cotton Colour Synthetics Delicates Wool Quick Rinse+Spin Spin 4. Temperature selection button Press the button repeatedly to cycle through the available water temperature options (cold , 40 °C , 60 °C and 95 °C). When pressing this button during washing, you can see the selected temperature in the display panel. 5. Spin selection button Press the button repeatedly to cycle through the available spin speed options. P1453 no spin, 600, 800, 1000, 1200 1400 rpm P1253 no spin, 600, 800, 1000, 1200 rpm P1053 no spin, 600, 800, 1000 rpm P853 no spin, 600, 800 rpm When pressing this button during operation, you can see the selected spin speed in the display panel. When all buttons are turned off NO SPIN. 6. Option button Press the button repeatedly to cycle through the available partial wash options Prewash . Rinse+ . Rinse Hold . Prewash +Rinse+. Prewash +Rinse Hold . Rinse+ +Rinse Hold . Prewash +Rinse+ +Rinse Hold . Cancle Note : Prewash is only available when washing cotton, synthetic or delicate. 7. Delay Start selection button Press this button repeatedly to rotate between the retarded start options available. (from 1 hour to 24hour, in 1 hour increments) 8. Start/Pause button Press to pause and restart programs. 9. (On/Off) button Press once to turn the washing machine on, press again to turn the washing machine off. If the washing machine power is left on for longer than 10 minutes without any buttons being touched, the power automatically turns off. What is the “Child Lock” function? -If you press the “Child Lock” button(Spin+Option button) longer than 2 sec during operation, this function is selected. -If once this function is selected, no change can be do...

Ce manuel est également adapté pour les modèles :
Rondelles - P1253 (206.06 kb)
Rondelles - P853 (206.06 kb)