Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Never clean the washer-dryer with a water jet. Risk of explosion. Never clean the washer-dryer with solvents. Risk of scalding Hot washing water must be cooled before draining. Wipe with a soft, damp cloth. Remove detergent and cleaning agent residue immediately. Do not clean with a jet of water. Remove any foreign bodies from the drum and rubber seals. Descaling the drum: – Only use a proprietary brand of descaler with corrosion inhibitor for washing machines for descaling the washer-dryer. – Observe the manufacturer's instructions regarding use and dosage. – After descaling and removing rust from the drum, run the Rinse ' + Spin B programme several times to remove any remaining acid. If any remaining metal objects (e.g. coins, paper clips, needles, nails) have caused rust spots: – Use chlorine-free cleaning agents; observe the manufacturer's instructions. Never use steel wool. If there are detergent or care product residues: • Pull out the detergent drawer as far as the stop. • Press on the blue zone labelled PUSH and take out the detergent drawer. • Clean the detergent drawer guide. • Remove the blue fabric softener compartment insert. • Clean the detergent drawer and fabric softener compartment insert under running water. • Insert the fabric softener compartment insert. • Insert the detergent drawer. Drain pump • Set the programme selector to Off. • Use a screwdriver to release the lock pins. • Tip the kick panel and pull upwards to remove. Draining the water Cleaning the drain pump • Take the drain hose out of the retainer. • Remove the plug from the drain hose and release the washing water. – The container for the drained water may have to be emptied several times. – When no more water runs out, replace the plug. • Place the drain hose into the retainer. • Unscrew the pump cover. – Clean the pump housing and remove any foreign objects. – Make sure that the impeller can turn freely. • Replace the pump cover and screw firmly in place. • Place the kick panel in the 4 clip-in slots and secure to the housing using the lock pins. Filter in the water supply hose Descaling the washer-dryer If no water runs into the washer-dryer, or only an insufficient amount, you must first reduce the water pressure in the supply hose: • Turn off the tap. • Choose any programme (except Rinse ' + Spin B / Empty t + Spin B). • Press the ! (Start/Pause) button. • Allow the programme to run for approximately 40 seconds. • Set the programme selector to Off. • Unplug the mains plug from the socket. • Unscrew the water supply hose from the tap. • Clean the filter with a small brush. • Reconnect the hose. • Turn on the tap. • Check whether water comes out of the end of the hose. • If water is escaping, check that the filter is correctly seated. This should not be necessary if the correct detergent dosage has been used. If it is necessary, however, proceed according to the descaling agent manufacturer's instructions. Suitable descalers can be obtained via our website or from our after-sales service –> page 24. What to do if... Risk of electric shock Repairs must only be carried out by customer services or authorised technicians. If repairs are needed, or if you cannot rectify a fault yourself with the help of the following table: • Set the programme selector to Off. • Disconnect the washer-dryer from the power supply. • Turn off the tap. • Call the after-sales service –> page 24. Fault code The is not closed properly. Try to close the door properly. The water protection system has been activated. Disconnect the appliance from the mains, turn off the tap and contact the after-sales service Water is not entering the appliance. See the fault Water is not flowing in. The water is not drained. See the fault Water is not drained. Maximum or minimum drying load not taken into account. HI/End or LO/End flash alternately in the display. See information for the Drying result not satisfactory fault. Other fault codes are only for use by the after-sales service. Make a note of the fault code to inform the after- sales service. Fault Possible cause Remedial action Programme does not start. The M (Start/Pause) button has not been pressed. Press the M (Start/Pause) button. A delayed start time has been selected. The washer-dryer starts once the delay time has elapsed. If necessary, change the finished in time –> page 14. Power cut. The delayed start time that was selected has been cleared. Make a new delayed start time selection or start a programme immediately: Press the M (Start/Pause) button. The door is not properly closed. Close the door. Plug not inserted properly into socket. Insert plug correctly. The maximum spin speed cannot be set. The maximum spin speed depends on the programme selected. Change programme as required. The water is not drained. Drain hose is twisted. Fit the drain hose correctly. Detergent pump is blocked. Clean the drain pump –> page 19. Detergent residues in the detergent drawer. Damp or lumpy detergent. Clean and dry t...
Ce manuel est également adapté pour les modèles :Rondelles - WK14D540HK/03 (583.35 kb)
Rondelles - WK16D540HK/01 (583.35 kb)
Rondelles - WK16D540HK/03 (583.35 kb)