Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
– ..(Easy-iron) selected? ..page 5. – Selected speed too low? ..page 5. ..The programme duration changes during the wash cycle. – Not a fault – the programme sequence is optimised for the particular wash process. This may result in changes to the programme duration in the display field. ..Spin cycle performed several times. – Not a fault unbalanced load detection system adjusts the imbalance. ..Residual water in the compartment for care products. – Not a fault the action of the care product is not affected. – Clean the insert if necessary ..page 9. ..Odour formation in the washing machine. – Run programme ..Cottons 90 °C without laundry. Use standard detergent. ..Status display....flashes. Foam may be coming out of the detergent drawer. – Too much detergent used? Mix 1 tablespoon of fabric softener with . litre of water and pour into dispenser II (not for outdoor and down-filled textiles!). – Reduce the detergent dosage for the next wash cycle. ..Intense noise formation, vibrations and “wandering” during the spin cycle. – Are the appliance feet fixed? Secure the appliance feet ..Installation instructions. – Transportation safety devices removed? Remove the transportation safety devices ..Installation instructions. ..Noises during spin and drain cycles. – Clean detergent-solution pump ..page 10. ..Display panel/indicator lamps do not function during operation. – Power cut? – Fuses triggered? Reset/change the fuse. – If the fault occurs repeatedly, call customer services. ..Programme sequence longer than usual. – Not a fault -unbalanced load detection system adjusts imbalance by repeatedly distributing the laundry. – Not a fault foam detection system active -adds an additional rinse cycle. ..Detergent residues on the laundry. – Occasionally, phosphate-free detergents contain water-insoluble residues. – Select ....Rinse / ....Spin or brush out the laundry after washing. If you cannot correct a fault yourself (switching on/off) or a repair is required: – Turn the programme selector to Off and remove the mains plug from the socket. – Turn off the water supply and call customer services ..Installation instructions. Instruction manual Washing machine Observe the safety instructions on page 8 . en Read these instructions and the separate installation instructions before operating the washing machine. 11What to do if ... ..Water is leaking out. – Attach/replace the drainage hose correctly. – Tighten the screw connection of the supply hose. ..No water supply. Detergent not dispensed. – ..Start/Reload not selected? – Tap not turned on? – Filter blocked? Clean the filter ..page 10. – Supply hose kinked or trapped? ..Washing machine door cannot be opened. – Safety function active. Programme stopped? ..page 4. – ....(without final spin) selected? ..page 3, 4. – Can be opened by emergency release only? ..page 9. ..Programme does not start. – ..Start/Reload or ..(Finished in) time selected? – Washing machine door closed? – Childproof lock active? Deactivate ..page 5. ..Detergent solution is not drained. – ....(without final spin) selected? ..page 3, 4. – Clean the detergent solution pump ..page 10. – Clean the waste pipe and/or drainage hose. ..Water not visible in the drum. – Not a fault water below the visible area. ..Unsatisfactory spin result. Laundry wet/too damp. – Not a fault the unbalanced-load detection system has cancelled the spin cycle because of uneven distribution of the laundry. Distribute small and large items of laundry evenly inside the drum. – ..(Easy-iron) selected? ..page 5. – Selected speed too low? ..page 5. ..The programme duration changes during the wash cycle. – Not a fault – the programme sequence is optimised for the particular wash process. This may result in changes to the programme duration in the display field. ..Spin cycle performed several times. – Not a fault unbalanced load detection system adjusts the imbalance. ..Residual water in the compartment for care products. – Not a fault the action of the care product is not affected. – Clean the insert if necessary ..page 9. ..Odour formation in the washing machine. – Run programme ..Cottons 90 °C without laundry. Use standard detergent. ..Status display....flashes. Foam may be coming out of the detergent drawer. – Too much detergent used? Mix 1 tablespoon of fabric softener with . litre of water and pour into dispenser II (not for outdoor and down-filled textiles!). – Reduce the detergent dosage for the next wash cycle. ..Intense noise formation, vibrations and “wandering” during the spin cycle. – Are the appliance feet fixed? Secure the appliance feet ..Installation instructions. – Transportation safety devices removed? Remove the transportation safety devices ..Installation instructions. ..Noises during spin and drain cycles. – Clean detergent-solution pump ..page 10. ..Display panel/indicator lamps do not function during operation. – Power cut? – Fuses triggered? Reset/change the fuse. – If the fault occurs repeatedly, call customer servic...
Ce manuel est également adapté pour les modèles :Rondelles - WM12E365BY/43 (2.11 mb)
Rondelles - WM12E365BY/44 (2.11 mb)
Rondelles - WM12E365BY/49 (2.11 mb)