Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Insert the drainage hose into its holder. 6. Refit the service flap and close it. To prevent detergent from flowing down the drain unused during the next wash cycle: pour 1 litre of water into compartment II and start the Empty .. programme. Drainage hose at the siphon Turn the programme selector to Off, disconnect the mains plug. 1. Loosen the hose clamp, remove the drainage hose carefully (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock Do not immerse the AquaStop safety device in water (it contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (apart from Spin ../ Empty ..). 3. Press .. (Start/Reload). Allow the programme to run for approx. 40 seconds. 4. Turn the programme selector to Off. Remove the mains plug from the socket. 5. To clean the filter: Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and Aqua-Secure models: Remove the hose from the back of the appliance, Remove the filter using pliers and clean the filter. 6. Connect the hose and check for leaks. Risk of scalding – Allow the detergent solution to cool down. – Turn off the tap. What to do if ... . . . . . . . . . . . . . . . Water is leaking out. – Attach/replac– Tighten the sce the drainage hose correctly. rew connection of the supply hose. No water supply. Detergent not dispensed. – (Start/Relo– Tap not turne– Filter may be – Supply hose kad) not selected? d on? blocked. Clean the filter a page 11. inked or trapped? Washing machine door cannot be opened. – Safety functio– (Rinse Hold a page 3, 4. – Can be openen active. Programme terminated? a page 4. = without Final spin) selected? d by emergency release only? a page 13. Programme does not start. – (Start/Relo– Washing mac– Childlock actiad) or ....(Finished in) time selected? hine door closed? ve? Deactivate it a page 5. Detergent solution does not drain. – (Rinse Hold a page 3, 4. – Clean the det– Clean the was= without Final spin) selected? ergent solution pump a page 11. te pipe and/or drainage hose. Water not visible in the drum. – Not a fault -water below the visible area. Unsatisfactory spin result. Laundry wet/too damp. – Not a fault -ththe spin cycle Distribute smadrum. – (Easy-iron) – Selected speee unbalanced-load detection system has cancelled because of uneven distribution of the laundry. ll and large items of laundry evenly inside the selected? a page 5. d too low? a page 5. Drum spins gently several times. – Not a fault -uimbalance. nbalanced-load detection system is adjusting the Residual water in the .. compartment for care products. – Not a fault -th– Clean the insee action of the care product is not affected. rt if necessary a page 10. Odour formation in the washing machine. – Run the CottoUse standard ns 90 °C programme with no load inserted. detergent. Status display . flashes. Appliance has detected a detergent overload. – Too much detMix 1 tablespinto compartm– Reduce the dergent used? oon of fabric softener with . litre water and pour ent II (not with outdoor or down fabrics). etergent dosage for the next wash cycle. Loud spinning, vibrations and “walking” during the spin cycle. – Appliance feeSecure the ap– Transport braRemove the trt fixed? pliance feet a Installation instructions. ces removed? ansport braces a Installation instructions. Display panel/indicator lamps do not function during operation. – Power cut? – Circuit breake– If the fault occrs tripped? Reset/replace the circuit breakers. urs repeatedly, call the after-sales service. Programme sequence longer than usual. – Not a fault -uimbalance by – Not a fault -forinse cycle. nbalanced-load detection system is adjusting the repeatedly redistributing the laundry. am detection system active -adds an additional Detergent residues on the laundry. – Occasionally, residues. – Use the Rinse 12 phosphate-free detergents contain water-insoluble cycle or brush out the laundry after washing. What to do if ... . E1. 2. 3. in Reload mode, ....(Start/Reload) flashes very quickly and an audible signal sounds – Water level too high. Not posClose door immediately if op– To continue the programme, sible to reload laundry. en. press (Start/Reload). If you cannot correct a fault yourself (switching on/off) or – Turn the programme selector to Off and remove the m– Turn off the water supply and call the after-sales servicmergency release e.g. in the evenThe programme continues when the power supply is restobe removed, the washing machine door can be opened aRisk of scalding. The detergent solution and laundry may be hot. Allow theDo not reach inside the drum if it is still turning. Do not open the door if you can see water through the gTurn the programme selector to Off and disconnect the mplug. Drain the detergent solution -> page 11. Pull the emergency release downwa...
Ce manuel est également adapté pour les modèles :Rondelles - WM12S444ME/04 (1.88 mb)
Rondelles - WM12S444ME/06 (1.88 mb)
Rondelles - WM12S444ME/07 (1.88 mb)
Rondelles - WM12S444ME/08 (1.88 mb)