Évaluations - 2, GPA: 3
(
)
)
|
Facilité d'utilisation
SELECTING A LOCATION 939mm544mm538mm Before you install the portable washer, select a location with the following characteristics: • A hard level surface (if the surface is uneven, see Adjusting The Adjustable Foot). • Away from direct sunlight. Direct sunlight may affect the acrylic coating, plastic and electrical components. • Adequate ventilation. • Away from sources of heat such as coal or gas. Make sure that the washing machine does not stand on its power cord. Ventilation openings must not be obstructed by carpeting when the portable washer is installed on a carpeted floor. ADJUSTING THE ADJUSTABLE FOOT LOOSENTIGHTENLEVEL ADJUSTABLE KNOBCORRECTINCORRECTINCORRECTFixed footCasterCasterFixed footAdjustable footCasterCasterFixed footADJUSTABLE FOOT If the floor is uneven adjust the adjustable foot (do not insert pieces of wood, or any other objects under the feet). Loosen the adjustable foot by turning the level adjustable knob with your hand until it is at the desired height. Tighten the adjustable foot by turning the level adjustable knob in the reverse direction. Place the washer on a sturdy flat surface. If the washer is placed on an uneven or weak surface, noise or vibration occurs (Allowable is 1°). For portable applications, the washing machine comes equipped with four north/south casters that can easily be installed to assist in the movement of the machine to and from the sink. Lay the unit on its back. Install the casters into the bottom of the base as indicated. Return the machine to the upright position. When the machine is positioned for operation set the height of the adjustment foot slightly higher than the front caster to prevent movement of the machine during wash and spin operation. NOTE: Not all movement will be totally eliminated, this is normal. INSTALLING THE NOISE PROOF PLATE Take the noise proof plate out of the package . The opening of the noise proof plate is at the bottom of the machine. Insert the noise proof plate into the washing machine base. Lay down the machine and secure the noise proof plate by fastening the two set screws. CONNECTING THE WATER SUPPLY HOSE The water supply hose must be connected to the washing machine at one end and to the water faucet at the other. Do not stretch the water supply hose. If the hose is too short and you do not wish to move the water faucet, replace the hose with a longer, high-pressure hose. Select appropriate faucet as shown in the figures below. If none of these faucets are available, use the faucet adapter provided. The end of faucet spout should be longer than 10mm (0.4”), or the connector cannot be fixed properly. Water leakage could develop. 1. Connect the water inlet hose to the faucet by turning the connecting nut. 2. Then connect the other end of water inlet hose to the cold connector in water mixing valve by turning the connecting nut. Rubber ring sealBe sure a rubber ring is inside the connecting nut. WATERINLET HOSECONNECTINGNUTCOLD WATERCONNECTORLID OF HOT WATERCONNECTORCONNECTINGNUT If you have both cold and hot water supplied, connect the inlet hoses by matching cold to cold and hot to hot. 1. Connect the water inlet hoses to the faucets by turning the connecting nuts. 2. Unscrew the lid of hot water connector in water mixing valve, and then connect the other end of water inlet hoses to the connectors in water mixing valve by turning the connecting nuts. WATER INLET HOSEWATERINLET HOSECONNECTINGNUTCOLD WATERCONNECTOR HOT WATERCONNECTORCONNECTINGNUTCONNECTINGNUT Be sure the rubber rings are inside the connecting nuts. WATER CONNECTION For normal kitchen-sink tap only use the inlet hose with cold water inlet. Connect the inlet hose to the male hose thread adapter by turning it clockwise to be fixed tightly. Make sure to insert the rubber ring enclosed. Then connect tightly to your sink. Note: Some faucets may require you to also use the female hose thread adapter between the male adapter and your sink faucet as shown below. Make sure the rubber ring is inserted and connect to your sink. If water leaks from faucet connection or washer connection, turn off water and tighten fully using a wrench. Be careful not to over tighten and damage water connection. Turn on water supply and make sure no leaks are present. DISCONNECTING THE INLET HOSE Dismantling the hose directly may cause water to splash due to the possible high water pressure in the hose, even after the faucet has been turned off. Please take off the hose as per following steps, even if the faucet is closed: CONNECTINGNUT • Turn off the faucet. • Turn on the power and let the machine run for about 5 seconds then turn it off. • Remove the connecting nuts from the faucet and washing machine. Note: If the washing machine is frequently used, it is not necessary to dismantle the inlet hose to avoid possible damage to the screws. POSITIONING THE DRAIN HOSE Connect the drain hose to the water outlet of the washing machine then fasten it with a pinchcork. Since only up drainage i...