Évaluations - , GPA:
(
)
)
Fabricant : Electrolux
Taille : 655.24 kb
Nom Fichier : cd4a6194-ab5d-4c2c-8c77-efb5f27b6671.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
This appliance complies with the requirements laid out in the EEC Directive 76/899. Voltage 240 V AC: Fuse rating 13 amps See rating plate for further information. This appliance meets VDE requirements. Particular regulations of local electricity authorities must be observed. This appliance conforms to EEC Directive No. 82/499/EWG on radio interference. 1 WARNING! Repairs to electrical appliances must only be carried out by trained personnel. Improper repairs may lead to serious risks for the user. Water connection 3 The washing machine is provided with safety devices preventing back- contamination of the water supply and complies with local water authority requirements. This appliance is designed to be permanently plumbed into your home’s water supply. Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Important! – Appliances for connecting to cold water must not be connected to hot water. – Only use new hose sets for the connection. Installation and connection instructions Water pressure The appliance is designed to operate within the following water pressure units. Minimum 1 bar (= 10N/cm2 = 0.1 Mpa), maximum 10 bar (= 100N/cm2 = 1 Mpa). • If more than 10 bar: Install a pressure-reduction valve upstream • If less than 1 bar: Unscrew the inlet hose from the appliance at the inlet solenoid valve and remove the flow regulator (to do this, remove the filter with needle nose pliers and remove the rubber washer behind the filter). Replace the filter. Installation and connection instructions Inlet Hose Connection A pressure hose of 1.35m in length is supplied. If a longer inflow hose is required, only a VDE-approved, complete set of hoses with fitted hose screw connections is permissible, available from AEG Service Force Centres. – Hose sets in lengths of 2.2m, 3.5m, and 5m are available for washing machines without Aqua-Control. – Hose sets in lengths of 2.0m, 2.9m and 3.9m are available for washing machines with Aqua-Control. Important! Never cut into pieces in order to extend the hoses! 3 Sealing rings are supplied either in the plastic nuts of the hose screw connection or in the enclosed pack. Do not use other seals! 0 1. Connect the hose with the angled connection to the machine. Important! – Do not lay the inlet hose vertically downwards, instead run it to the right or left as shown in the diagram. – Tighten firmly to prevent leakage but do not use excessive force. 2. Connect the hose with the straight connection to a water tap with a screw thread R 3/4 (inches) Important! Only tighten the screw connection by hand. 3. By slowly opening the water tap before putting the washing machine into operation, check that the connection is free of leaks. Installation and connection instructions Water Drainage The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic “U-Piece“ supplied. The standpipe should have an internal diameter of approximately 38 mm (see diagram) thus ensuring there is an air break between the drain hose and standpipe. Important! It is essential to lay the drainage hose without kinks. When discharging into a standpipe ensure that the top of the curve in the hose end is no more than 90 cm (35.4’’) and no less than 60 cm (23.6’’) above floor level. The upright standpipe should have a minimum, length of 30 cm (12’’) from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water. Longer drain hoses are available in lengths of 2.7 and 4 metres from your AEG Service Force Centre. Installation and connection instructions If you intend the drain hose from the washing machine to empty into a sink, make sure that the sink is empty and the plug hose is not blocked. Use the plastic “U-Piece“ supplied. Important! The end of the drainage hose must not be submerged in the pumped-out water. Otherwise, the water could be sucked back into the ap pliance. Pump head of greater than 1m Every washing machine includes a wash water pump for the removal of wash and rinse water, which can pump fluids through the outlet hose up to a height of 1m, measured from the surface on which the machine stands. For pump heads of greater than 1m please contact your local AEG Service Force Centre. Installation and connection instructions Technical Data Height adjustment of about +10/-5mm Load (depending on programme) up to 6kg Area of use Domestic Drum spin speed see Rating Plate Water pressure 1-10bar (=10–100N/cm2 = 0.1–1.0MPa) Dimensions (dimensions in mm) Warranty conditions Warranty conditions Great Britain Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we w...