Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Between 800-1200mm Back Front Soft object Screw Bottom plate Install the water inlet hose Install the water inlet hose Use the new hose and the old hose should not be reused. 1. Insert a new flat washer into each end of the inlet hoses. Firmly put the washers in the coupling. 2. Connect the water inlet hoses to the water faucet. Use the new hose sets supplied with the washer. Any other old hose sets should not be used. You may have to use pliers to tighten the coupling. Do not over tighten because you may cause damage to the valve. Note: 3. Connect the other ends to their respective cold and hot water inlet valve located at the rear of the washer Check the connection between the water inlet hose and the water tap 4.Fasten the nut. Swing it gently to confirm if it's suitable. 1.Swaying the hose gently to confirm if it is fastened stable. 2.After installation, open the tap to check if it leaks. 3.Do not bend the hose with overstrain. 4.Before each usage please check if the connection between the water inlet hose and the water tap, and the connection between the water inlet hose and washer are firm, so as to prevent dropping from improve Installation position. Water absorption cushion Nut of the water inlet hose Jointer of the water inlet valve Take down the water inlet hose 1.Close the water tap. 2. Pull off the water inlet hose from the water tap and washer. 5 1.Preparation before washing Confirm if there's special requirement for the laundries. Clear the pocket. Take out the coins , sand, hairpins etc. Fasten the buttons and zippers. When the pulsator is running ,the buttons of the laundries may cause noise. For the sake of discretion, please put the laundries with buttons into other laundries. The quantity of the laundries shall not exceed the rated value. The big laundries like the jeans shall be put in loosely. Preparation before washing 1.Connect the water inlet hose 2.Confirm that the washing machine is earthed reliably.Then insert the power plug into the receptacle.Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Do not put down the drain hose. 4.Slanting or uneven ground may result in unstable working or abnormal noise. Please make the machine stand horizontally. Pay attention to followings before washing the laundries 0.8m H 1.2m a. Check if the laundries are applicable for washing with machine. b. Divide the laundries with unfast color from other laundries. c. Put those laundries difficult to absorb water into water with hand. d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil, please apply detergent in advance, which can make it easier to remove the soil. e. For those laundries that may get lint ball and those with long fur, turn it over before putting in. f. Do not put those laundries polluted by chemicals directly into the washing machine. For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into mesh bag for washing. 6 2.Put in the laundries The capacity of washing of the machine refer to the largest weight of the standard laundries under dry condition that can be washed in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity. The thickness ,size , type of the cloth will influence the actual washing capacity. It is suitable to put inreasonable amount of laundries and the laundries can be turned round in washing for one time washing. Do not select more than "L" water level for laundries less than 1.0kg ,so as to avoid splashing of water. 3. Usage of the detergent If you open the top lid,the machine will stop working and alarm in spinning process. 4. Close the top lid How to use washing powder Washing powder with poor quality or long-time storage may get caked. Please clean the detergent box duly in usage. Dissolve directly inside the washing machine: (not applicable for fuzzy and reserve program) 1.Add some water(select the 2.Add washing powder. Run for about 30s to fully dissolve the powder. Then push the"start/pause" button. 3.Put in laundries. Select suitable water level. Push the "start/pause"button again. " L " water level) Quick dissolving of washing powder: 1.Prepare warm water of 30 C and container. 2. Add washing powder while stirring to dissolve it completely. It is not recommended to use rich-foam washing powder. If you select save program, it is suggested to use liquid detergent instead of washing powder to guarantee the washing effect. Please add suitable washing powder as per the laundries quantity, the set water level and water quantity. It is suggested to add washing powder into the box directly under fuzzy program and reserve program. 7 How to use the whitener Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub. Avoid using whitener on laundries with color or pattern as they are prone to lose color. The whitener shall not touch the laundries directly. Refer ...