Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
See to the figure: Back Front Bottom plate Screw Soft items Push the lint filter downward to location for lint filter. How to change the direction of the drain hose 1.The height of the drain hose shall be less than 10cm, or the drainage will not be smooth, and cost such long time that the machine may stop at mid way. 2.Do not trample or press the drain hose. If the drain hose is too long, cut it at mid point. To make smooth drainage, cut the front end of the hose slantingly. 4.If extra drain hose is needed, please make separate purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m. 5.If the extra hose is too long, cut it either at A or at B point. <10cm Usage of the drain hose The drain hose shall drain smoothly 5 1.Loosen the fastening screw of the back cover to take off the back cover. Be careful not to do it by force to prevent breaking the claw of the back cover.(as indicated in Figure 1) 3.Extend the drain hose from the installation hole at the right side of the base frame. Fix the drain hose onto the base frame with the drain hose frame and fasten the screw. Then set the drain hose hook on the drain hose and hang the drain hose on the hanging hole of the cabinet. (As indicated in Figure 3) 4.To install the back cover, first hang the lower beard of the back cover on the cabinet, then push the claws at the two side and the upper end from bottom to top to resume the original setting. Be careful not to do it by force. Then fasten the screw (two points) (as indicated in Figure 4). 2.Take off the drain hose from the cabinet. Nip the drain hose outlet slightly. Dismantle the drain hose hook. Loosen the fixing screw of the drain hose frame to dismantle the drain hose frame. Pull the drain hose into the cabinet from the left side of the base frame. Drain hose frame Nip the drain hose outlet and take off the drain hose hook Screw Figure 3 Back cover Figure 1 Screw Top claw Claws at the two sides Lower bread Figure 4 Figure 2 Water tap,suitable Water tap,not suitable It is required that the front end shall be longer than 10mm. The outlet end surface of the tap shall be flat and smooth. If not please file it to avoid leakage. 2.Loosen the screw till the water tap can be accessed. Put the jointer of the water inlet hose on the tap. See to Figure 2. (If the tap diameter is too large and the jointer can not be set on the water tap, please loosen the four screws and take out the bushing in the jointer. See to the figure3.) 1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component. See to Figure 1. Remarks: Before twisting the fastening nut, the thread is 4mm above the upper surface of the nut. After twisting the fastening nut, the thread is 2mm above the upper surface of the nut. See to Figure 6. 4.Take off the nameplate. Twist the fastening nut as per the indication of the figure. See to Figure 5. 3.Fasten the four screws evenly. See to Figure 4. >10mm Outlet end surface Nut About 4mm before twisting About below 2mm after twisting Screw Screwdriver Mark label bushing Figure 2 Figure 5 Figure 1 Figure 4 Figure 3 Figure 6 Slider Water inlet pipe jointer Water inlet pipe Locking lever Install the water inlet hose Confirm the water tap Connection between the water inlet hose jointer and the water tap 6 1.Do not take off the water absorption cushion. Please check if the cushion is dropped or damaged before each usage. If it happens please contact our after-sale department immediately. 2.Put the nut of the water inlet hose on the valve jointer. 3.Fasten the nut. Swaying it gently to confirm if it's suitable. 1.Close the water tap. 2.Press the locking lever. Push down the slider. Then pull off the water inlet hose. If the machine is used more than once every week, the jointer of the water inlet hose can be kept on the tap to prevent damaging the fixing screw. 1.Push down the slider. Insert the water inlet hose into the jointer. 2.Hang the lock lever to the jointer. Release the slider till a click sound is heard. Locking lever Slider Water absorption cushion Nut of the water inlet hose Jointer of the water inlet valve Slider Jointer of the water inlet hose Locking lever Connection between the water inlet hose and the washing machine Connection between the jointer of the water inlet hose and the water inlet hose Check the connection between the jointer of the water inlet hose and the water tap Take down the water inlet hose 1.Swaying the hose gently to confirm if it is fastened stable. 2.After installation, open the tap to check if it leaks. 3.Do not bend the hose with overstrain. 4.Before each usage please check if the connection between the jointer of the water inlet hose and the water tap, and the installation of the water inlet hose are firm, so as to prevent dropping from improper Installation position. 7 Note : The new hose- set supplied with appliance are to be used and the old hose...