Évaluations - , GPA:
(
)
)
Fabricant : Haier
Taille : 1009.21 kb
Nom Fichier : 09096449-09ec-4599-910a-00dc67d7c7d8.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
"A3" represents 103 minutes. It displays abnormal symbol in abnormal situation. (See to Page15) (HOURS LATER) (MINUTES) About less than 2mm after twisting Figure 3 Connection between the water inlet hose jointer and the water faucet Bushing About 4mm before twisting 2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet. See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise it may leak water. See to Figure 3.) 1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component. See to Figure 1. Water faucet,not suitable Install the water inlet hose Screw It is required that the front end shall be longer than 10mm. The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage. remark: Before installation, the threading is 4mmabove the upper surface of the nut. After installation, the threading is 2mm above the upper surface of the nut. See to figure 6. Figure 6 Sign plate 4.Take off the nameplate. Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet. See to Figure 5. Figure 2 Screw nut Screw knife 3.Fasten the four screws evenly. See to Figure 4. water inlet hose jointer Figure 5 Outlet end surface Slider Figure 1 Water faucet,suitable water inlet hose Figure 4 Lock level Confirm the water faucet PROGRAM/RESERVE button Push down the program/ reserve button. You can select one program of ten which is standard,soak heavy, gentle,save,cotton, single wash,rinse spin,single spin,tub clean, air dry; Push the"program/ reserve" button to set the reserve wash program morethan two seconds continuously; When the "reserve" function is activated, the indicator light of the program you have set will be off. The "reserve (hour)" and "time remain" indicator lights will be on; During reserve procedure, push the "reserve" button to display the reserve mode.To change the running program or cancel the reserve setting, you need to switch off the power and make new selection; Digital display Fuzzy logic control 10 water level selection Connection between the water inlet hose and the washer 1.Do not take off the water absorption cushion. Please check if the cushion is dropped or damaged before each usage. If it happens please contact our after-sale department immediately. 2 Put the nut of the water inlet hose on the valve jointer. 3 Fasten the nut. Swing it gently to confirm if it's suitable. nut of the water inlet hose jointer of the water inlet valve water absorption cushion. Dismantle the water inlet hose 1. Close the water faucet. 2. Press the locking lever. Push down the slider. Then pull of the water inlet hose. If the machine is used frequently, the jointer of the water inlet hose can be kep t on the faucet to prevent damaging the fixing screw. Locking level Slider START/PAUSE button After the power is switched on,press it to start the machine During working,push it to pause. During pause,push this button to restart and go on working a 5 Use the operation buttons Description of operation button Indicator mode and meaning START PAUSE TIME REMAINED RESERVE Attention: 1. The digitron displays the remained time and process alternately during the washing machine working. 2. The process function is not selected solely .(see to Page 12) SOAK HEAVY SAVE SINGLE WASH SINGLE SPIN TUB CLEAN GENTLE COTTON RINSE SPIN AIR DRY SOAK WASH SPIN RINSE Program INDICATION OF PROCESS (NO CHOOSING) STANDARD Connection between the jointer of the water inlet hose and the water inlet hose 1.Push down the slider. Insert the water inlet hose into the jointer. 2 Hang the lock lever to the jointer. Release the slider till a click sound is heard. Locking level the jointer of the water inlet hose Slider 1.Swing the hose gently to confirm if it is fastened stable. 2.After installation, open the faucet to check if it leaks. 3.Do not bend the hose with overstrain. 4.Before each usage please check if the connection between the jointer of the water inlet hose and the water faucet, and the installation of the water inlet hose are firm, so as to prevent dropping from improper installation position. Check the connection between the jointer of the water inlet hose and the water faucet Flashing: indicate the running program On: indicate the program about to run, or indicate the selected mode Off: If you open the top lid,the machine will stop working and alarm in spinning process. 4. Close the top lid The capacity of washing of the machine refer to the largest weight of the standard laundries under dry condition that can be washed in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity. The thickness ,size , type of the cloth will influence the actual wash...