Évaluations - 3, GPA: 3
(
)
)
|
Facilité d'utilisation
A part that is damaged should be properly repaired or replaced by an authorised service facility, unless otherwise indicated in this Instruction Manual. Defective switches must be replaced by an authorised service facility. Do not use a tool if the switch does not turn the tool on and off correctly. 19. Guard against electric shock. Prevent body contact with grounded objects such as water pipes, radiators, cookers and refrigerator enclosures. 20. Use only approved parts. When servicing, use only identical replacement parts. Use an authorised service facility to fit replacement parts. WARNING. The use of an accessory or attachment, other than those recommended in this Instruction Manual, may present a risk of personal injury. Additional safety rules for Heat guns • A fire may arise if the appliance is not use with care. • Be careful when using the appliance in places where there are combustible materials, such as inflammable liquids, rags, wood shavings and the like. • Do not apply the heat to the same place for a long time. • Do not use in the presence of an explosive atmosphere. • Heat may be conducted to combustible materials which are out of sight • Place the appliance on its stand whenever you place it down and after use and allow to cool before storage; • Never leave the appliance unattended when in use. • Rags, cloths, cord, string, wood shavings and the like should never be left around the work area. • Support the work properly. • If you are interrupted when operating the appliance, complete the process and switch off before looking up. • When using the appliance, use safety equipment including safety goggles or shield, breathing mask and protective clothing including safety gloves. Wear goggles Wear earmuffs Wear a breathing mask • Never attempt to use the appliance to dry animals, clothing or hair. • Never use this appliance as a hair dryer. • Always use in ventilated areas. • Do not leave the appliance unattended when in use. • This product is designed for light domestic use only, it is not designed for industrial purposes and whilst every care has been taken to make hot air gun safe, accidents can happen. By following the simple safety guide you can avoid accidents. WARNING: During application the heat nozzle must be kept at least 16mm away from the work piece. This is to allow air flow. 1 5 4 3 2 Know your product 1. Heat Nozzle2. Guard Sleeve3. Body4. LED Temperature Indicator5. Variable Temperature Control Dial6. Two speed rocker switch7. Wire Stand8. Power CordAccessories 9. Heat Spreader10. Heat Reflector11. Heat Concentrator12. Heat Deflector13. Paint Scraper14. Scraper Handle Scrapers15. Scrapers 6 14 7 8 11 9 8 15 13 10 12 Features: Two Speed Rocker Switch: The rocker switch can be adjusted to 3 positions and these are: Variable Temperature Control The variable temperature control enables the temperature to be set and adjusted between 50°C and 650°C, depending upon the type of material and the work to be carried. Temperature Indicator The temperature indicator gives the temperature during operation. 6 LED’s are placed on the box lid. Each one represents a different temperature range: Note: The temperature indicator gives the temperature for reference only. Safety Cut Out This unit is equipped with a safety cut-out device which will operate if the internal temperature gets too high. Should this feature activate, switch off the unit and wait for the unit to cool down. When the unit has cooled sufficiently normal operation can be resumed. PLEASE NOTE: The reset time of the hot air gun’s safety cut-out fuse is approximately 30 minutes, after which normal operation can resume. Assembling the Wire Stand For convenience, the wire stand should be set up before operating; therefore the tool can be rested when Position 0: Stop/Off LED No: Colour Temperature (C) 1 Yellow 50o 2 Yellow 100o 3 Green 200o 4 Green 350o 5 Red 500o 6 Red 650o Position 1: 50° - 550°C Position 2: 50° - 650°C necessary. A Phillips #1 screwdriver (not supplied) is needed during the assembly. 1.Place the wire stand to the bottom of the handle, ensuring that the ends of the stand align themselves with the holes on the handle. 2.Insert the Phillips screw on one side between the end of the stand and the hole of the handle. Use the Phillips screwdriver to secure the screw. 3.Repeat this process on the other side of the handle. Note: Before you commence with the assembly, make sure that the plug of the unit is disconnected from the mains supply. Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 4...