Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the nailer if the WCE trip mechanism is not operating properly. Personal injury may occur. 1. Disconnect the air supply from the nailer. 2. Remove all nails from the magazine (see Loading/ Unloading). 3. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding. 4. Reconnect air supply to the nailer. 5. Depress the Work Contact Element (WCE) against the work surface without pulling the trigger. The nailer must not operate . Do not use the tool if it operates without pulling the trigger. Personal injury may result. 6. Remove the nailer from the work surface. The Work Contact Element (WCE) must return to its original down position. The nailer must not operate . Do not use the tool if it operates while lifted from the work surface. Personal injury may result. 7. Pull the trigger and depress the work contact element (WCE) against the work surface. The nailer MUST NOT operate . 8. Depress the Work Contact Element (WCE) against the work surface. Pull the trigger. The nailer MUST operate . An improperly functioning tool must not be used. Do not actuate the tool unless the tool is placed firmly against the work piece. Loading /Unloading The Nailer 1. Always disconnect the tool from the air supply before loading fasteners. 2. Insert nails into rear slot as shown. 3. Pull pusher back until it is behind nail clip, then release. 4. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except always disconnect the air hose before unloading. Adjusting the Nail Penetration The tool is equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface. 1. Adjust operating pressure so nails are driven consistently. Do not exceed 110 psi. 2. To drive the nail shallower, turn the wheel (C) to right to the extent desired. 3. To sink a nail deeper, turn the wheel (C) to left to the extent desired. 4. Make sure trigger and work contact element (WCE) move freely up and down without binding or sticking after each adjustment. Adjusting The Direction Of The Exhaust The tool is equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired. 1 2 1 2 Rotate 1 2 (C) 6 Operating Instructions CHN20103 User - Maintenance Instructions Clearing A Jam From The Tool 1. Disconnect the air supply from the tool. 2. Remove all nails from the magazine (see Loading/ Unloading). Failure to do so will cause the nails to eject from the front of the tool. 3. Undo latch by pulling out and down. The wire latch will disengage from the hooks on the nose. 4. The door can now be rotated, exposing the jammed fastener. 5. Remove the jammed fastener, using pliers or a screwdriver if required. 6. Rotate door back into the closed position. 7. Extend the wire latch and place over the hooks on the nose. 8. Close the latch by pushing the latch up and in until the latch snaps into place. 9. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding. Technical Ser vice Please call our Tool Hotline at 1-800- 543-6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual. Fastener And Replacement Parts Use only headless micropins, 16 gauge. Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number. Tool Repair Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently. Assem bly Procedure For Seals When repairing a tool, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non-detergent oil or equivalent, must be added through the air line before testing. Storage The tool should be stored in a cool dry place. Fasteners The following Campbell Hausfeld finishing nails are available at local retail stores. If you need help locating any item, call customer service at 1-800-543-6400. Campbell Hausfeld nails meet or exceed ASTM Standard F1667. Model Length Shank Gauge Finish Head Collation Nails Per Stick Nails Per Box FB005060 2 inch 16 Gauge Galvanized Brad Adhesive 50 2500 FB160025 1 inch 16 Gauge Galvanized Brad Adhesive 50 1000 FB160040 1-1/2 inch 16 Gauge Galvanized Brad Adhesive 50 1000 FB160065 2-1/2 inch 16 Gauge Galvanized Brad Adhesive 50 1000 Interchange Information Nails used in the Campbell Hausfeld CHN201 Finishing Nailer will a...