Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
Figure 15 12 Operating Instructions and Parts Manual CHN71500 Maintenance (Continued) FasteNer INterCHaNge INForMatIoN Can use 3/8 inch to 7/8 inch pins from the following branded 23 g micropinners: • Senco FP10 • Air Locker P630 • Porter Cable PIN100 • Grex P635 • Max NF235A Troubleshooting Guide Stop using nailer immediately if any of the following problems occur. Serious personal injury could result. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center. SYMPTOM CAUSe SOLUTION Air leaking at trigger valve O-Rings in trigger valve housing are Replace o-rings area. damaged Air leaking between housing 1. Damaged o-rings 1. Replace o-rings and nose. 2. Damage to bumper 2. Replace bumper Air leaking between housing 1. Loose screws 1. Tighten screws and cap. 2. Damaged seal 2. Replace seal Tool skips driving fastener 1. Worn bumper 1. Replace bumper 2. Dirt in nose piece 2. Clean drive channel 3. Dirt or damage prevent fasteners 3. Clean magazine or pusher from moving freely in magazine 4. Damaged pusher spring 4. Replace spring 5. Inadequate air flow to tool 5. Check fitting, hose, or compressor 6. Worn o-rings on piston or lack of 6. Replace and lubricate o-rings lubrication 7. Damaged o-rings on trigger valve 7. Replace o-rings 8. Air leaks 8. Tighten screws and fittings 9. Cap seal leaking 9. Replace seal 10. Defect in automatic nail length plate 10. Clear problem with plate Tool runs slow or has loss of 1. Tool not lubricated sufficiently 1. Lubricate nailer power 2. Broken spring in cylinder cap 2. Replace spring 3. Exhaust port in cap is blocked 3. Replace damaged internal parts Fasteners are jammed in tool 1. Guide on driver is worn 1. Replace guide 2. Fasteners are not correct size 2. Use only recommended fasteners 3. Fasteners are bent 3. Replace with undamaged fasteners 4. Magazine or nose screws are loose 4. Tighten screws 5. Driver is damaged 5. Replace driver 13 Operating Instructions and Parts Manual For Replacement Parts or Technical Assistance, Call 1-800-543-6400 Please provide following information: Address any correspondence to: - Model number Campbell Hausfeld - Serial number (if any) Attn: Customer Service - Part description and number as shown in parts list 100 Production Drive Harrison, OH 45030 U.S.A. 2 3 5 6 8 7 10 11 20 16 17 18 19 21 1 4 9 15 14 13 12 70 72 73 74 22 23 24 25 26 27 28 41 40 42 29 30 31 32 33 37 38 39 71 65 64 63 62 61 69 46 68 36 67 36 34 35 43 44 45 44 47 66 48 49 41 50 59 60 58 51 52 53 54 57 56 36 55 Figure 16 – Repair Parts Illustration for Air Powered Pin Nailer, model CHN71500AV CHN71500 14 Operating Instructions and Parts Manual CHN71500 Replacement Parts List for Brad Nailer ref. Part No. description Number Qty. ref. Part No. description Number Qty. 1 Exhaust deflector — 1 51 Magazine plate — 1 2 Socket head cap 52 Spring pin — 2 screw -M4 x 16 k 4 53 Limiter assembly — 1 3 Cylinder head cap — 1 54 Pusher — 1 4 Gasket n 1 55 Pusher seat — 1 5 Exhaust seal n 1 56 Spring pin k 1 6 Spring n 1 57 Magazine door — 1 7 O-ring n 1 58 Shoulder pins — 2 8 Head valve — 1 59 Pusher spring n 1 9 O-ring n 1 60 Spring n 1 10 O-ring n 1 61 Socket head cap 11 O-ring n 1 screw -M4 x 10 k 2 12 Collar — 1 62 Magazine end cap — 1 13 Piston ring s 1 63 Magazine cap spring n 1 14 O-ring s 1 64 Magazine thumb latch — 1 15 Piston s 1 65 Pin — 1 16 Driver blade s 1 66 Socket head cap 17 O-ring n 1 screw -M4 x 18 k 1 18 Cylinder — 1 67 Washer — 1 19 O-ring n 1 68 Washer — 1 20 Restrictor plate — 1 69 Magazine bracket — 1 21 Bumper n 1 70 Hand grip — 1 22 Body — 1 71 Nut-M4 k 1 23 Nozzle n 1 72 O-ring n 1 24 Spring pin n 2 73 Inlet end cap — 1 25 Work contact element (WCE) 74 1/4 -18 I/M (M) Swivel plug SV567600AV 1 bracket — 1 rePlaCeMeNt Parts kIts 26 WCE spring n 1 s Drive blade assembly SKN19900AV 27 WCE — 1 n Complete rebuild kit SKN23900AV 28 No-mar tip n 1 — Not Available 29 Trigger valve head — 1 k Standard hardware item -available at your local 30 Valve seal n 1 hardware store 31 Trigger valve — 1 32 O-ring n 1 33 Trigger valve stem spring n 1 34 Upper drive guide — 1 35 Drive guide cover — 1 36 Socket head cap screw -M4 x 8 k 5 37 Trigger valve stem — 1 38 O-ring n 2 39 Trigger spring n 1 40 Trigger assembly — 1 41 Retaining o-ring — 2 42 Pin — 1 43 Socket head cap screw -M4 x 14 k 2 44 Socket head cap screw -M4 x 14 k 2 45 Lower driver guide — 1 46 Recoil decal housing — 1 47 Straight pin — 2 48 Magazine — 1 49 Screw-M4x10 k 2 50 Magazine slide plate — 1 15 Operating Instructions and Parts Manual CHN71500 Reminder: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping. Warranty 1. DURATION: From the date of purchase by the original purchaser as follows: One (1) Year. 2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6...