WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. #9629TS Printed in China ...................................................................................................................................................................................................................................................................................................................................................

1 -6 Model W1783 (Mfg. Since 2/07) OPERATIONS Loading When replacing nails in your Model W1783, follow these guidelines: Nails.................... L-Shaped Cleat Nails Length: .................................... 1"–2" Capacity: ................................... 100 Note: Use 11.2" nails to install 1.2" flooring, and 2" nails to install 3.4" flooring. To load your nailer, do these steps: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Slide a strip of nails, pointed-end down, into the rear of the

Repair or replace damaged parts. 21. NEVER LEAVE UNATTENDED TOOL CONNECTED TO AIR. Disconnect the air hose and do not leave tool until it is relieved of any built up pressure. 22. NEVER ALLOW UNTRAINED USERS TO USE THIS TOOL WHILE UNSUPERVISED. 23. IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP USING TOOL. Seek formal training or research books or magazines that specialize in pneumatic tools. 24. BE AWARE OF HOSE LOCATION WHEN USING PNEUMATIC TOOLS. Hoses can easily become a tripping hazard w

Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as needed for satisfactory results. An in-line filter/lubricator/regulator unit, can be installed as depicted in Figure 1. This filter/lubricator/regulator unit will protect your tool from damaging water build-up, allow you to adjust and maintain regulated air pressure to your tool, and save you the inco

5. Nails are wrong angle. 1. Use correct nails. 2. Use undamaged, clean nails. 3. Tighten magazine. 4. Replace worn or damaged parts. 5. Use correct angle nails. Nailer does not fire. 1. Nailer is not lubricated. 2. Nail is jammed in magazine or discharge area. 3. Piston shaft is damaged. 4. Air pressure too low. 1. Follow lubricating instructions. 2. Clear nailer magazine or discharge area. 3. Replace piston shaft. 4. Check/increase air pressure. Air blows out of exhaust cap; nailer will not fi

Figure 3. Loading nails into magazine. 4. Slide the nails all the way down to the nose of the nailer. 5. Release the magazine pusher by pulling back on the pusher and pressing in on the catch lever. Operating If you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer connects to the air supply. To operate your nailer, do these steps: 1. Connect

If you have comments about this manual, please contact us at: Woodstock International, Inc. Attn: Technical Documentation Manager P.O. Box 2309 Bellingham, WA 98227 Email: manuals@woodstockint.com Tool Data Staple Size .......................... 18 Gauge Staple Length........................ 5.8"-15.8" Staple Crown ...............................1.4" Magazine Capacity...............100 Staples Air Inlet.................................." NPT Weight ................................. 3.2 lbs. Oper

Clean inspect the parts for cracks, wear, or burrs. 9. Place a new O-ring on the new piston and apply a thin film of the nailer lubricating oil on the O-ring. 10. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide at the bottom of the cylinder. The new piston should easily slide into the cylinder. DO NOT force the piston into the cylinder! If the piston is not easily inserted, double-check the alignment of the piston shaft with t

....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking 1. Loose screws in housing. 1. Tighten screws. between housing 2. Damaged O-ring. 2. Replace O-ring and hose. 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking between housing and cap. 1. Damaged seal. 1. Replace damaged seals. Tool skips staples 1. Excessive air pressure. 1.Reduce air pressure to tool. while discharging. 2. Air leaks. 3.