Évaluations - 5, GPA: 3.6
(
)
)
|
Facilité d'utilisation
• Do not tamper with controls. • Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out. • Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product. • Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials. • Clean lint screen before or after each load. • Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt. • The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel. See installation instructions for grounding requirements. SAVE THESE INSTRUCTIONS INSTALLATION INSTRUCTIONS Check that you have everything necessary for correct installation. Proper installation is your responsibility. • Flat-blade screwdriver • Safety glasses • Adjustable wrench that • Duct tape opens to 1 in. (2.54 cm) or hex-head socket • Caulking gun and wrench (for adjusting compound (for installing dryer feet) new exhaust vent) • Level • Gloves • Wire stripper (direct wire • Tin snips (new vent installations) installations) • #2 Phillips screwdriver • V4in. nut driver or socket wrench Parts supplied Remove parts package from dryer drum. Check that all parts are included. 4 Leveling legs NOTE: Do not use leveling legs if installing the dryer on a pedestal. Parts needed Check local codes. Check existing electrical supply and venting. See "Electrical Requirements" and "Venting Requirements" before purchasing parts. • For close-clearance installations between 31.5 in. (80.01 cm) and 37 in. (93.98 cm), see "Plan Vent System" section for venting requirements. I< 87,, >1 (63.98cm) Mobile home installations require metal exhaust system hardware available for purchase from your local Sears store or Sears Service Center. For further information, please call 1-800-4-MY-HOME _ (1-800-469-4663). s Pe 5ss s Are you placing the dryer on a pedestal? You can purchase a pedestal separately for this dryer, This pedestal will add about 14 in. (35.56 era) to the height of your unit for a total height of approximately 52 in. (132,08 em). Optional pedestal The pedestal is available in three colors White -Part Number 42842 Biscuit -Part Number 42844 Graphite -Part Number 42846 To order, call your local Sears store. For further information, please call 1-800-4-MY-HOME _ (1-800-469-4663). Lee@:on Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Place dryer at least 18 inches (46 cm) above the floor for a garage installation. Failure to do so can result in death, explosion, or fire. You will need • A location that allows for proper exhaust installation. See "Venting Requirements." • A separate 30 amp circuit. • A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See "Electrical Requirements." • A sturdy floor to support the total dryer weight of 200 Ibs (90.7 kg). The combined weight of a companion appliance should also be considered. A level floor with a maximum slope of 1 in. (2.5 cm) under entire dryer. (if slope is greater than 1 in. [2.5 cm], install Extended Dryer Feet Kit, Part No. 279810.) Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level. • For a garage installation, you will need to place the dryer at least 18 in. (46 cm) above the floor. If using a pedestal, you will need an additional 6 in. (15.24 cm). Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended. Install the dryer where it is protected from water and/or weather. Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector. Installation clearances The location must be large enough to fully open the dryer door. Dryer Dimensions [128,_' era) * Most installations require a minimum 51/2in. (14 cm) clearance behind the dryer for the exhaust vent with elbow. See '_/enting Requirements." Minimum installation spacing for recessed area, custom undercounter or closet installation The following dimensions shown are for the minimum spacing allowed. • Additional spacing should be considered for ease of installation and servicing. Additional clearances might be required for wall, door and floor moldings. Additional spacing of 1 in. (2.5 cm) on all sides of the dryer is recommended to reduce noise transfer. For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable. • Companion appliance spacing should also be considered. Cus...