Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
The buzzer signal is permanent off. 3. The buzzer is by default always off. You can use BUZZER button to activate or deactivate sound but machine does not memorize your selection. Water hardness Water contains, a variable quantity of limestone and mineral salts of which quantities vary according to geographical locations thus varying its conductivity values. Relevant variations of the conductivity of the water compared to those prefixed by the factory could slightly influence the residual humidity of the laundry at the end of the cycle. Your dryer allows you to regulate the sensitivity of the drying sensor based on conductivity values of the water. 1. Turn the programme selector to any programme. 2. Press simultaneously the DELICATE and BUZZER buttons and hold down for approx. 5 seconds. The current setting is on the lights: light "EINDE (end) "– low conductivity <300 micro S/cm, light "COOLING" – medium conductivity 300-600 micro S/cm,lightS "COOLING "and "EINDE (end)"– high conductivity >600 micro S/cm 3. Press the START PAUSE button sequentially until you set desired level. 16 16 Technical data 4. To memorize setting press simultaneously the DELICATE and BUZZER buttons or turn knob to OFF position Technical data This appliance conforms with the following EU Directives: – 2006/95/EC dated 12.12.2006 Low Voltage Directive – 89/336/E.E.C dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC – 93/68/EEC dated 22.07.1993 CE Marking Directive Height x width x depth 85 x 60 x 58 cm Drum volume 108 l Depth with loading door open 109 cm Height can be adjusted by 1.5 cm Weight when empty approx. 32.5 kg Loading volume (depends on programme)1) max. 7 kg Voltage 240 V Required fuse 13 A Total power 2600 W Energy efficiency class C Energy consumption (7 kg of cotton, pre- drained at 1000 rpm) 2) 3.9 kWh Average annual energy consumption 263.1 kWh Use Domestic Permissible ambient temperature + 5°C to + 35°C Consumption values The consumption values have been established under standard conditions. They may deviate when the machine is operated in domestic circumstances. Programme Energy consumption in kWh / average dry- ing time in min. COTTONS CUPBOARD DRY 2) 3) 3.9 / 103 (7 kg load pre-drained at 1000 rpm) COTTONS IRON DRY 2) 3.05 / 78 (7 kg load pre-drained at 1000 rpm) SYNTHETICS CUPBOARD DRY 2) 1.15 / 32 (3 kg load pre-drained at 1200 rpm) 1) Different loading volume data may be needed in some countries as a result of different measuring methods. 2) in accordance with EN 61121 Installation 17 Installation Appliance positioning • It is recommended that, for your convenience, the machine is positioned close to your washing machine. • The tumble dryer must be installed in a clean place, where dirt does not build up. • Air must be able to circulate freely all round the appliance. Do not obstruct the front ventilation grille or the air intake grilles at the back of the machine. • To keep vibration and noise to a minimum when the dryer is in use, it should be placed on a firm, level surface. • Once in its permanent operating position, check that the dryer is absolutely level with the aid of a spirit level. If it is not, raise or lower the feet until it is. • The feet must never be removed. Do not restrict the floor clearance through deeppile carpets, strips of wood or similar. This might cause heat built-up which would interfere with the operation of the appliance. The hot air emitted by the tumble dryer can reach temperatures of up to 60°C. The appliance must therefore not be installed on floors which are not resistant to high temperatures. When operating the tumble dryer, the room temperature must not be lower than +5°C and higher than +35°C, as it may affect the performance of the appliance. WARNING! Should the appliance be moved, it must be transported vertically. WARNING! The appliance must not be installed behind the lockable door, a sliding door or a door with a hinge on the opposite side to that of the appliance. Removing transport safety packaging CAUTION! Before use all parts of the transport packaging must be removed. 1. Open loading door 2. Pull off adhesive strips from inside machine on top of drum. 18 18 Installation 3. Remove foil hose and polystyrene padding from the machine. Fitting the vent hose To simplify the installation, there is a choice of vent outlets: one at the back, the others in the left and right-hand side. Connect the hose to whichever is the more convenient by pulling the ring nut (A) from the vent outlet at the back, screwing it on to the hose and pushing it firmly back into place. The unused vents should now be sealed with the special snap covers provided. If the hose is long and the room temperature low, the moisture might condense to water inside the hose. This is an unavoidable natural phenomenon. To prevent this water from Iying in the hose or flowing back into the tumble dryer, it is advisable to drill a small hole (via. 3 mm) in the lowest point of the hose and t...