Log:
Évaluations - 3, GPA: 4.3 ( )

Instructions Samsung, Modèle BED70W

Fabricant : Samsung
Taille : 3.89 mb
Nom Fichier : 58364bbb-a02d-41c4-8617-f36bd86d513c.pdf
Langue d'enseignement: enfr
Aller à la télécharger



Facilité d'utilisation


Tighten screws. 5. Tighten the strain relief screws. 6. Insert the tab of the terminal block cover into your Dryer’s rear panel slot. Secure the cover with a hold-down screw. 1. External ground connector 2. Green or bare copper wire of power cord 3. 3/4 in. (1.9 cm) UL-listed strain relief 4. Center silver-colored terminal block screw _ _ 5. Grounding wire (green/yellow) |[ 6. Neutral wire (white or center wire) 6. With a level, check your Dryer and make necessary adjustments to the leveling legs. 7. At this time, make sure all gas connections (on gas models), exhaust and electrical connections are complete. Plug in your Dryer, and check operation by using the checklist below. 8. (GAS MODEL ONLY) The burner may not ignite initially due to air in the gas line. Allowing your Dryer to operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes, turn your Dryer off and wait 5 minutes. Be sure the gas supply to your Dryer has been turned on. In order to confirm gas ignition, check the exhaust for heat. FINAL INSTALLATION CHECKLIST □ Dryer is plugged into electrical outlet and properly grounded. □ Exhaust ductwork is hooked up and joints taped. □ Plastic flexible duct is NOT used. □ Used rigid or stiff-walled flexible metal vent material. □ Dryer is level with all legs firmly on the floor. □ Gas models - gas is turned on with no gas leaks. □ Start your dryer to confirm that it runs, heats, and shuts off. Installing your dryer _15 BED70W-02486B_EN.indd 15 2008-01-09 ¿ÀÈÀ 6:53:14 installing your dryor DRYER EXHAUST TIPS A Plastic or non-metal flexible duct presents a potential fire hazard. 1. Let your Dryer exhaust the air easily. 2. Use a 4” diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new Dryer. Be sure that the vent flap opens and closes freely. Inspect and clean the exhaust system annually. Don’t let a poor exhaust system slow drying by: 1. Restricting your Dryer with a poor exhaust system. 1 2. Using a plastic, thin foil, or non-metal flexible duct. 3. Using unnecessarily long duct runs with many elbows. 4. Allowing crushed or clogged ducts and vent. 16_ Installing your dryer BED70W-02486B_EN.indd 16 2008-01-09 ¿AEA 6:53:16 2 DOOR REVERSAL 1. Unplug the power cord. 2. Remove two door hinge screws. 3. Lift the door and remove from the dryer. 4. Remove a screw on the Frame Front 5. Remove two screws on the opposite side of the door hinge. 6. Remove two screws from the holder lever. 7. Remove one black screw from the door hinge. 8. Reassemble the black screw in the other hole. 9. Reassemble the screw (Step 4) on the Frame Front 10. Place the door on the other side and reattach it to the dryer. 11. Reassemble the holder lever. 12. Reassemble the screws in the remaing holes. I 3 (Q y o c d y


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories