Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
9 Grounding requirements - Gas dryer (USA and Canada) 1. The dryer is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. 2. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician. DO NOT cut or remove ground prong from the plug. Grounding typeGrounding type wawall receptaclll receptacle PoPower cord withwer cord with 3-prong3-prong grgrounded plugounded plug Do not,Do not, underunder anany ciry circumstances,cumstances, cut,cut, remoremoveve, or bor bypass thypass the grgrounding prounding prong.ong. Gas connection 1. Remove the shipping cap from gas pipe at the rear of the dryer. DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. conversion kit must be installed by a qualifi ed gas technician. 2. Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved pipe from gas supply line to the 3/8 inch (0.96 cm) pipe located on the back of the dryer. Use a 1/2 inch to 3/8 inch (1.27 cm to 0.96 cm) reducer for the connection. Apply an approved thread sealer that is resistant to the corrosive action of liquefi ed gases on all pipe connections. All connections must be wrench-tightened Flare Union Flare Union GAS FLOW Manual Shutoff Valve Closed Open Flexible Connector Inlet Pipe on Back of Dryer elppiN The supply line must be equipped with an approved manual shutoff valve. This valve should be located in the same room as the dryer and should be in a location that allows ease of opening and closing. Do not block access to the gas shutoff valve. 3. Open the shutoff valve in the gas supply line to allow gas to fl ow through the pipe. Wait a few minutes for gas to move through the gas line. Shutoff Valve - Open position to dryer from gas supply 4. Check for gas system leaks with a manometer. If a manometer is not available, test all connections by brushing on a soapy water solution. -EXPLOSION HAZARD -NEVER test for gas leaks with an open fl ame. 10 11 Electrical connection (non-Canada) - 3 wire cord 1. Turn off power supply to outlet. 2. Remove the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3. Install a UL-approved strain relief according to the power cord/strain relief manufacturer’s instructions in the power cord entry hole below the access panel. At this time, the strain relief should be loosely in place. 4. Thread an UNPLUGGED, UL-approved, 30 amp. power cord, NEMA 10-30 type SRDT, through the strain relief. 5. Attach the power cord neutral (center wire) conductor to the SILVER colored center terminal on the terminal block. Tighten the screw securely. 6. Attach the remaining two power cord outer conductors to the outer, BRASS colored terminals on the terminal block. Tighten both screws securely. 3-wire receptacle (NEMA type 10-30R) Internal ground (GREEN screw) Install UL-approved strain relief here Terminal screw recovery slot Line 1 (BRASS terminal) Neutral (SILVER terminal) Line 2 (BRASS terminal) Access cover screw Terminal block Neutral (center wire) 30 AMP NEMA 10-30 7. Follow manufacturer’s guidelines for fi rmly securing the strain relief and power cord. 8. Reinstall the terminal block cover. DO NOT remove internal ground in a 3-wire system!! Neutral terminal - ELECTRICAL SHOCK HAZARD - Failure to disconnect power source before servicing could result in personal injury or even death. - ELECTRICAL SHOCK HAZARD - Do not make a sharp bend or crimp wiring/conductor at connections. If moving dryer from a 4-wire system and installing it in a 3-wire system, move the internal ground from the center terminal back to the GREEN screw next to the terminal block. If a terminal screw falls during cord installation, it can be retrieved in the terminal screw recovery slot below the access panel. 4-wire receptacle (NEMA type 14-30R) Electrical connection (non-Canada) - 4 wire cord 1. Turn off power supply to outlet. 2. Remove the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3. Install a UL-approved strain relief according to the power cord/strain relief manufacturer’s instructions in the power cord entry hole below the access panel. At this time, the strain relief should be loosely in place. 4. Thread an UNPLUGGED, UL-approved, 30 amp. power cord, NEMA 14-30 type ST or SRDT, through the strain relief. 5. Disconnect the internal (BLACK) dryer harness ground wire from the (GREEN) ground screw next to the terminal block. 6. Attach the ground (GREEN) power cord wire to the cabinet with the ground (GREEN) screw. Tighten the screw securely. 7. Move the internal dryer harness ground (BLACK) wire to the terminal block and attach it along with the neutral (WHITE) power cord wire conductor to the center, SILVER colored terminal on the terminal block. Tighten the sc...