Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
Failure to do so can result in fire or electrical shock. Prepare minimum 5 ft (1.52 m) of length in order for dryer to be replaced. First, strip 3 ‘/2 inches (8.9 cm) of outer sheath from end and strip 1 inch of insulation from each conductor. Then, put the hooked shape end of the wire under the screw of the terminal block (hooked end facing rightward) and pinch the hook together and tighten the screw securely. gr ^ 1. Connect neutral wire (white) of power cord to center terminal block screw. 2. Connect red and black wires to the left and right terminal block screws. 3. Make sure that the strain relief screw is tightened. Be sure that all terminal block nuts are on tight and power cord is in right position. Center terminal block screw (silver) Neutral grounding wire (white) Neutral grounding wire (white) Strain relief External ground connector Option 1: 4-wire connection with a power supply cord. lf your local codes or ordinances do not allow the use of a 3-wire connection, or you are installing your dryer in a mobile home, you must use a 4-wire connection. 4-wire receptacle (NEMA type 14-30R) 4-prong plug Spade terminals with upturned ends —Ground prong Neutral prong 4-prong plug Ground prong Neutral prong 3/4 in. (1.9 cm) UL approved strain relief Ring terminals Center terminal block screw (silver) Neutral grounding wire (white) Neutral wire (white or center wire) Strain relief Green wire of power cord External ground connector 1. Connect neutral wire (white) of power cord to center terminal block screw. 2. Connect red and black wires to the left and right terminal block screws. 3. Connect ground wire (green) of power cord to external ground screw and move neutral ground wire of appliance and connect it to center screw. 4. Make sure that the strain relief screw is tightened. Be sure that all terminal block nuts are on tight and power cord is in right position. 21 Part 5| ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS Option 2: 3-Wire connection with a power supply cord. Option 3: Optional 3-wire connection. lf your local codes or ordinances permit the connection of a frame-grounding conductor to the neutral wire, use these instructions. If your local codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, use the instructions under Section 1: Optional 3-wire connection. Center terminal block screw (silver) Neutral grounding wire (white) Neutral grounding wire (white) Strain relief External ground connector If your local codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, use the instructions under this section. Neutral grounding wire (Green) Neutral wire (white) External ground connector Separate ground wire 1. Connect neutral wire (white) of power cord to center terminal block screw. 2. Connect ground wire of appliance and neutral wire of power cord to center terminal block screw. 3. Connect red and black wires to the left and right terminal block screws. 4. Make sure the strain relief screw is tightened. Be sure that all terminal block nuts are on tight and power cord is in right position. 5. Connect a independent ground wire from external ground connector to proper ground. 22 Part 6| ELECTRICAL REQUIREMENTS FOR GAS DRYERS 120 Volt, 60 Hertz, with 3-Prong Grounding Plug Following are additional instructions regarding electrical connections and requirements for gas dryers. Warning: The wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1, and all applicable local regulations. Please contact a qualified electrician to check your hom’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer. Failure to do so can result in fire or electrical shock. Electrical Requirements for Your Dryer: a) Please note that the wiring diagram is provided inside the dryer control hood. Label all wires prior to disconnection when servicing the dryer, because wiring errors can cause serious injury to you and your dryer. b) Your dryer is designed to be used on a separate branch, polarized, three-wire, effectively grounded, 120 Volt, 60 Hertz, AC (alternating current) circuit protected by a 15 Ampere fuse, equivalent fuse or circuit breaker. c) Use separately fused circuits for washers and dryers, and DO NOT operate a washer and a dryer on the same circuit. STANDARD 120 VOLT, 60 HERTZ, 3-WIRE EFFECTIVELY GROUNDED CIRCUIT A WARNING! • Do not overload the circuit by operating other appliances on the same circuit when this appliance is operating, by using an extension cord to connect the dryer to the power source, or by using any adapter to allow additional cords to connect to the same outlet. • Failure to do so can result in fire or electrical shock. J!i WARNING! • DO NOT modify the plug provided with the dryer. If it does not fit the outlet in your...
Ce manuel est également adapté pour les modèles :Séchoirs - DLE3733W (12.13 mb)
Séchoirs - DLE3733S (12.13 mb)
Séchoirs - DLG3744W (12.13 mb)