Évaluations - 3, GPA: 3
(
)
)
|
Facilité d'utilisation
The dryer must not be operated, without the cover in place. Door Reversal Instructions 31 Door Reversal Instructions The door opening direction can be changed if required. 1 Warning! Before reversing the door, isolate the appliance from the mains supply. Proceed as follows to reverse the door opening direction: 0 Un-screw the screws A on the front panel of the appliance. 0 Take-off the door by displacing it horizontally. 0 Un-screw the screws B on the inside of the door and take-off the hinges C. 0 Unscrew and take-off the locking block D. 0 Release the coverplates E, F and G with a thin screwdriver by pressing on the latching device, displace them to the side. Take them out and insert them again on the opposite side. 0 Screw-on the hinges C and the locking block D on the opposite side of the door. 0 Screw-off the door catch H and remove it and pull-off the plug. F A C B E D F E H A C B J G Door Reversal Instructions 0 Take-out the latched catch covering J and pull-off the plug. 0 Connect the door catch H and the catch covering J on the respective opposite side to the plug, insert into the break-out and screw-down or latch into position. 0 Push the door with the hinges into the breakouts provided for them in the front panel of the appliance and firmly attach it with the screws. 0 After changing-over the door, check that the DOOR button functions correctly. 1 Warning! The appliance is safe again for operation only when all plastic parts have been mounted. Programming possibilities Programming possibilities The electronic control system of your laundry dryer provides you with the possibility to adapt some functions of the dryer permanently to your requirements. Purpose Execution "Laundry protection": If you want to "lock" the selected drying program (the selected program setting cannot be changed during the drying process at the program selector or with the SPECIAL CARE or QUICK button): When "Washing Protection" is enabled, the drying programme always runs at reduced heater power (SPECIAL CARE Function). If you always want to be reminded by an audible signal at the end of the program: If you remove condensate via an external condensate drain-off and wish to permanently suppress the EMPTY WATER indication: When a drying program is set at the program selector and the START button has been pressed: - Hold the SPECIAL CARE button depressed for five seconds. The program execution display flashes for five seconds and the laundry protection is then switched-on. If an attempt is nevertheless made to change the program setting, the program execution display flashes; after pressing the SPECIAL CARE or QUICK button, it flashes for five seconds; on turning the program selector it flashes until the program selector is returned to the initial setting. To cancel the laundry protection: - Hold the SPECIAL CARE button depressed for five seconds. The program run indicator flashes for five seconds, then it is lit steady for five seconds; laundry protection is cancelled. 1) Ensure that the program selector is not in the setting LIGHT or OFF. 2) Hold the AUDIBLE SIGNAL button depressed for at least five seconds. The AUDIBLE SIGNAL display lights; a short audible signal is sounded. The selected setting is therewith fixed-programmed. If you want to cancel this setting: 3) Proceed as described under item 1) and 2). The display AUDIBLE SIGNAL disappears. 1) Set the programme selector to LIGHT. 2) Hold the AUDIBLE SIGNAL button depressed for five seconds. The PROG. TIME display shows U for normal function and & for external condensate drain-off. 3) Briefly press the AUDIBLE SIGNAL button to choose between U and & . 4) Turn the program selector. The selected setting is therewith fixed-programmed. Programming possibilities Purpose Execution Adjusting the drying result: If at the end of the programme you always want the washing to be somewhat dryer or somewhat damper than with the standard setting and you want to adjust the tumble dryer’s recognition of the degree of dryness accordingly: 1) turn the programme selector to the LIGHT position. 2) Hold down the DELAY TIMER button for five seconds. The current setting appears in the PROGRAMME TIME display: H1 is the standard setting, with H0 the washing will be dryer, with H2 the washing will stay damper. 3) Keep pressing the DELAY TIMER button until the value you require appears in the display. 4) Turn the programme selector. The selected setting is then saved. Technical data Technical data Height x Width x Depth 85x60x60cm Depth with the door open 117cm Height adjustable from 1.0/–0.4cm Empty weight approx. 46 kg Load (depending on the program) max. 5kg (Different loads in some countries are due to different measuring methods) Power consumption in acc. with IEC 1121 s.e. 3.5 kWh (5 kg Cotton, spun at 800 revolutions per minute, program COTTON CUPBOARD DRY) Area of use Household Permissible ambient temperature +5°C up to +35°C ; This appliance complies with the following EC directives: – 73...
Ce manuel est également adapté pour les modèles :Séchoirs - LAVATHERM 57700 (452.55 kb)
Séchoirs - LAVATHERM 57700 (452.55 kb)
Séchoirs - LAVATHERM 57700 (452.55 kb)