Évaluations - 2, GPA: 4.5 ( )

Fabricant : Cissell Taille : 341.47 kb Nom Fichier : Langue d'enseignement:

2. Operate dryer using full-size loads. Very large loads use extra energy. Very small loads waste energy. 3. Dry light-weight fabrics separately from heavy fabrics. You will use less energy and get more even drying results by drying fabrics of similar weight together. 4. Clean the lint screen area daily. A clean lint screen helps give faster, more economical drying. 5. Do not open the dryer door while drying. You let warm air escape from the dryer into the room. 6. Unload the dryer as soon as it stops. This saves having to re-start your dryer to remove wrinkles. Page 27 Operating Instructions - Two Timer Model (Illustration) Page 28 Operating Instructions - Two Timer Model OPERATING INSTRUCTIONS TWO TIMER MODEL OPERATINStep 1. G INSTRUCTIONS - TWO TIMER MODEL After loading the dryer with water washed clothes, close the loading door. Step 2. Turn the 60 minute drying (heat) timer to the desired time. The drying cycle light will be on. Step 3. Turn the 15 minute cooling (air) to the desired time. The cooling light will come on after the drying finishes. TEMPERATURE Step 4. Select the temperature desired: High Heat 185°F exhaust temperature, heavy fabrics and hard to dry. Normal 185°F exhaust temperature, cottons and linens. Permanent Press 150°F exhaust temperature, synthetic blends. Low Heat 135°F exhaust temperature, delicate, sheer fabrics. Step 5. Turn “on/off” toggle switch to “on” and press the “push to start” button to start the drying and cooling cycles. Step 6. To shut the dryer off at any time during the cycles, switch the “on/off” switch to “off”. Page 29 Automatic Computerized Drying Control DESCRIPTION FEATURES DRYNESS SENSOR DESCRIPTION The Automatic Computer Drying Control is used to manage the drying and cooling cycles of one clothes dryer. The operator has the flexibility to select either automatic or timed drying and either automatic or timed cooling. When automatic is selected, the drying cycle will be terminated when the clothes are dry. A dryness sensor "feels" the clothes and signals the control when they are dry. In the timed mode, the operator sets the time and temperature for the load. FEATURES: • Automatic/Timed drying selection. • Automatic/Timed cooling selection. • Fabric selection (in automatic mode only). • LED display of cycle time. • Drying temperature range of 100° F - 195° F (Timed mode only). • Drying time range of 0-60 minutes (Timed mode only). • Cooling time range of 0-60 minutes (Timed mode only). • Repeat Last Cycle feature. • Safety tumble cycle. • Reversing/Non-reversing selection (option). • Power off after 30 minutes of non-use. DRYNESS SENSOR When in the auto drying mode, the length of the cycle is controlled by a “dryness sensor”. The sensor works on a “capacitor charge time” principle. The electronic circuit looks at the charge on the capacitor in the dryness circuit. When the capacitor is fully charged, the circuit ends the drying cycle. One side of the capacitor is connected to a dryness probe located in the center of the basket. Wet clothes hitting the probe will “discharge” the capacitor or prevent it from reaching full charge. As the clothes dry, they have less effect on discharging until finally it is fully charged, ending the drying cycle. The time to charge the capacitor with no clothes load is listed: FABRIC SELECTION CHARGE TIME Heavy 11.5 Minutes Cotton 5.5 Minutes Permanent Press 5.5 Minutes Delicate 5.5 Minutes Page 30 Automatic Computerized Drying Control LED DISPLAY MESSAGES LED DISPLAY MESSAGES Display Condition “__0” load. Normal display between loads. Dryer is waiting for the next “012” timed mode. Normal display during drying/ cooling cycle. Display shows “time used” when in automatic and “time remaining” when in “012” (Flashing) The door has been opened. Close the door and press START to continue the cycle. “-S-” (Flashing) The dryer is in the Safety Tumble mode. The cycle has ended and the dryer can be unloaded. “_PF” (Flashing) There has been a power failure. To restart the dryer, press ON and START. To terminate the cycle press OFF/STOP. “FFF” (Flashing) The temperature sensor has failed. The dryer cannot be run until it is repaired. “-A-” Indicates the automatic mode has been selected. (DRYING TIME and COOLING TIME only). Page 31 Automatic Computerized Drying Control ON OFF/STOP START COOLING TIME DRYING TIME DRYING TEMPERATURE FABRIC SELECTOR OPERATION OF CONTROL PANEL (See drawing on page 33) 1. ON Turn the control on. If dryer is not used for 30minutes, the power will turn off. Press “on” for power. 2. OFF/STOPTurns the control off or stops the dryer during acycle. 3. START Starts the cycle or re-starts it off. 4. COOLING TIME In timed mode, with this button held down, the set cooling time in minutes will be shown in the display. To change the time, use the “up” and “down” buttons while cooling time button is down. The cooling time cannot be changed when automatic cooling is selected, “-A-” will show in the displaywhen this button is h...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :