Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
In some installations there may be some sounds associated with air movement throughout the dryer, including the air duct, blower, and exhaust system. This is normal and can vary with load size and type. C. GAS VALVE (Gas models only.) The flow of gas is controlled by electric solenoids. During operation there may be a clicking sound as the valve opens and closes to control the gas flow. D. GAS BURNER (Gas models only.) When the burner is operating, there may be sounds generated as the air flow mixes with the gas flame. This noise is normal and will only occur when the gas is ignited in the combustion tube. 1 Prepare load for drying. • Dry items of similar fabric, weight and construction in the same load. • Separate dark items from light-colored items. Separate items that shed lint from those that attract lint. • Check for stains which may not have been removed in washing. Repeat stain removal process and wash again before drying. Dryer heat may permanently set some stains. • Place delicate or small items in a mesh bag. • Be sure buckles, buttons and trim are heatproof and won’t damage the drum finish. Close zippers; fasten hooks and Velcro®-like fasteners. Tie strings and sashes to prevent snagging and tangling. 7 Operating Instructions IMPORTANT Clean the lint filter after every load. 2 Check that the lint filter is clean and in place. .NOTE Over-drying can cause wrinkles, shrinkage, lint, harshness and a build up of static electricity. .NOTE If a setting is not available for the cycle selected, the indicator will not light. 3 Load the dryer and close the door. • Load items loosely. The average wet load will fill the drum 1/3 to 1/2 full. Items need room to tumble freely for even drying and less wrinkling. • If desired, place a dryer fabric softener sheet on top of the load at the beginning of the cycle. • To save energy and time and avoid uneven drying and wrinkling, do not overload the dryer. • When drying large items, dry only two or three items at a time. Fill out the load with small and medium sized items. • For delicate or very small loads, add two or three similar items to improve tumbling action. 4 Select the appropriate cycle and settings for each load. • A suitable drying temperature, dryness level and options will automatically be indicated for the cycle selected. See the “Dryer Settings Chart” for more details. • To change the drying temperature and dryness level, press the Temperature or Dryness buttons to scroll to the desired settings. • To select or delete an option, press Options; then, while the indicator is blinking, press Select. The indicator will light when the option has been selected. It will no longer be lighted when the option has been deleted. • Adjustments made to a cycle will be remembered and recalled each time that cycle is selected in the future. • To return to factory settings, press the Start/Pause and Select buttons at the same time and hold until the signal sounds. • Turn the cycle selector knob in either direction to select the cycle desired. The indicator for that cycle will be illuminated. • The estimated drying time for Auto Dry cycles or the actual drying time for Timed Dry cycles will be displayed. Operating Your Dryer, continued 5 Start the cycle. • To add or remove items when the dryer is running, open the door. The dryer will stop when the door is opened. Allow the drum to come to a complete stop before reaching inside. • Close the door and press Start to resume the cycle. 6 When the cycle ends, remove items immediately and hang or fold. Press and hold both for ten seconds to return to factory settings. operatInG InStructIonS This manual covers many models and not all cycles, options, or features listed are available on every model. Console shown above for reference only. Your model may differ. cycle Selection Turn the cycle selector in either direction to the cycle desired. The indicator for that cycle will be illuminated. Follow the fabric care label instructions on items to be dried. for best results To change the cycle once it has begun, press the cancel button before selecting a new cycle. Just turning the cycle selector knob to another selection will not change the cycle. If the selection is changed after the cycle starts, the indicator lights will blink, the signal will beep and “Err” will be displayed. The signal will beep and the status lights will flash, but the original cycle will continue. auto Dry cycles Auto Dry cycles take the guesswork out of selecting the correct drying time for each load. Moisture sensing bars at the back of the dryer drum sense the moisture level of the load as it tumbles through the heated air. With Auto Dry cycles, the load will automatically be dried at the selected temperature to the desired dryness level. Auto Dry cycles save time and energy and protect fabrics. The estimated drying time will be displayed for about 5 minutes. Then the outside of the display will light up in a circular track to indicate the drying time is ...