Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FORA3-WIRESYSTEM. Electrical requirements for gas dryer: CIRCUIT -Individual, properly polarized and grounded 15 amp. branch circuit fused with 15 amp. time delay fuse or circuit breaker. POWER SUPPLY -2-wire, with ground, 120 volt, single phase, 60 Hz, Alternating Current. POWER SUPPLY CORD -The dryer is equipped with a 120 volt 3-wire power cord. GROUNDING CONNECTION -See “Grounding requirements” in Electrical Installation section. Grounding type wall receptacle Do not, under any circumstances, cut, remove, or bypass the grounding prong. Power cord with 3-prong grounded plug 5Installation Requirements WARNING FIREHAZARDFailure to follow these instructions can create excessivedryingtimesandfirehazards. WARNING FIREHAZARDDonotinstallaclothesdryerwithflexibleplasticormetalfoilventingmaterials.Flexibleventingmaterials are known to collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire. Exhaust system requirements If your present system is made up of plastic duct or metal foil duct, replace it with a rigid or semi-rigid metal duct. In Canada and the United Statesifmetal(foiltype)ductisinstalled,itmustbe of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers and in the United States must also comply with the Outline for Clothes Dryer Transition Duct, UL standard 2158A. Also, ensure the present duct is free of any lint prior to installing dryer duct. Useonly4inch(10.2cm)diameter(minimum)rigidorflexiblemetalductandapprovedventhoodwhichhasaswing-outdamper(s)thatopenwhenthe dryer is in operation. When the dryer stops, the dampers automatically close to prevent drafts and the entrance of insects and rodents. To avoid restricting the outlet, maintain a minimum of 12 inches(30.5cm)clearancebetweentheventhoodand the ground or any other obstruction. CorrectIncorrectCorrectIncorrectThe following are specific requirements for proper and safe operation of your dryer. Gas supply requirements WARNING EXPLOSIONHAZARDUncoated copper tubing will corrode when subjectedtonaturalgas,causinggasleaks. Use ONLY black iron, stainless steel, or plastic- coated brass piping for gas supply. 1. InstallationMUSTconformwithlocalcodes,orin the absence of local codes, with the National FuelGasCode,ANSIZ223.1(latestedition). 2. Thegassupplylineshouldbe1/2inch(1.27cm)pipe. 3. Ifcodesallow,flexiblemetaltubingmaybeused to connect your dryer to the gas supply line.ThetubingMUSTbeconstructedofstainless steel or plastic-coated brass. 4. ThegassupplylineMUSThaveanindividualshutoff valve. 5. A1/8inch(0.32cm)N.P.T.pluggedtapping, accessiblefortestgaugeconnection,MUSTbe installed immediately upstream of the gas supply connection to the dryer. 6. ThedryerMUSTbedisconnectedfromthegas supply piping system during any pressure testing of the gas supply piping system at test pressuresinexcessof1/2psig(3.45kPa). 7. ThedryerMUSTbeisolatedfromthegassupplypiping system during any pressure testing of the gas supply piping system at test pressures equal toorlessthan1/2psig(3.45kPa). 8. Connections for the gas supply must comply with the Standard for Connectors for Gas Appliances,ANSIZ21.24.5Installation Requirements WARNING FIREHAZARDFailure to follow these instructions can create excessivedryingtimesandfirehazards. WARNING FIREHAZARDDonotinstallaclothesdryerwithflexibleplasticormetalfoilventingmaterials.Flexibleventingmaterials are known to collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire. Exhaust system requirements If your present system is made up of plastic duct or metal foil duct, replace it with a rigid or semi-rigid metal duct. In Canada and the United Statesifmetal(foiltype)ductisinstalled,itmustbe of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers and in the United States must also comply with the Outline for Clothes Dryer Transition Duct, UL standard 2158A. Also, ensure the present duct is free of any lint prior to installing dryer duct. Useonly4inch(10.2cm)diameter(minimum)rigidorflexiblemetalductandapprovedventhoodwhichhasaswing-outdamper(s)thatopenwhenthe dryer is in operation. When the dryer stops, the dampers automatically close to prevent drafts and the entrance of insects and rodents. To avoid restricting the outlet, maintain a minimum of 12 inches(30.5cm)clearancebetweentheventhoodand the ground or any other obstruction. CorrectIncorrectCorrectIncorrectThe following are specific requirements for proper and safe operation of your dryer. Gas supply requirements WARNING EXPLOSIONHAZARDUncoated copper tubing will corrode when subjectedtonaturalgas,causinggasleaks. Use ONLY black iron, stainless steel, or plastic- coated brass piping for gas supply. 1. InstallationMUSTconformwithlocalcodes,orin the absence of local codes, with ...
Ce manuel est également adapté pour les modèles :Séchoirs - EWMED65H (2.83 mb)
Séchoirs - 134709300 (2.83 mb)
Séchoirs - 137018200 A (2.83 mb)