Log:
Évaluations - 5, GPA: 4.2 ( )

Instructions Cobra Electronics, Modèle CPI 875

Fabricant : Cobra Electronics
Taille : 1.04 mb
Nom Fichier : 216ef764-23e6-daf4-7d4e-dbfd51636324.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


CAUTION Do not connect the inverter and another AC source (such as a generator or utility power) to the AC wiring at the same time. The inverter will be damaged if its output is connected to AC voltage from another source. Damage can even occur if the inverter is switched off. CAUTION Do not connect the inverter to an AC branch circuit that has high-power consumption loads. It will not operate electric heaters, air conditioners, stoves, and other electrical appliances that consume more than 800 watts. CAUTION Loose connectors result in excessive voltage drop and may cause over heated wires and melted insulation. CAUTION Reverse polarity connections (positive to negative) will blow internal fuses in the inverter and may permanently damage the unit. Such damage is not covered by the warranty. CAUTION Remove any jewelry (watch, ring, etc.). Be careful not to short circuit the battery with any metallic object (wrench, etc.). WARNING 115 volt AC power is potentially lethal. Do not work on AC wiring when it is connected to the inverter (even if it is switched off) unless the DC power source is physically disconnected from the inverter. Also, do not work on AC wiring if it is connected to another AC power source such as a generator or the utility line. WARNING You may observe a spark when making the connection because current can flow to charge the capacitors in the inverter. Do not make this connection in the presence of flammable fumes. Explosion or fire may result. Thoroughly ventilate the battery compartment before making this connection. Nothing Comes Close to a Cobra® 10273_CPI875_PH2 7/10/07 6:04 PM Page 8 1110 Turning Your Inverter On or Off • Be sure to have your power inverter properly installed before attempting to turn the unit on (see installation page 5). To turn the power inverter on: 1. If a DC power supply is being used as the power source, switch it on. 2. On the left side panel, switch the On/Off Switch to on. The inverter is now ready to deliver AC power to your loads. If several loads are to be operated by the inverter, turn them on separately, after the inverter has been turned on. This will ensure that the inverter does not have to deliver the starting currents required for all the loads at once. To turn the power inverter off: 1. On the left side panel, switch the On/Off Switch to off. NOTE The On/Off Switch turns the control circuit in the inverter on and off. It does not disconnect power from the inverter. NOTE When the switch is in the off position, the inverter draws no current from the battery. When it’s in the on position, but no power is being supplied to the load, the inverter draws less than 500 milliamperes from the battery. This is low current draw. It would take more than a week to discharge a 100 ampere-hour battery at this rate depending on the age of the battery. Power Consumption IntroOperationCustomerAssistanceWarrantyNotesNoticeSecondary Power On and Off IntroOperationCustomerAssistanceWarrantyNotesNoticeMain IntroOperationCustomerAssistanceWarrantyNotesNoticeMain Comes Close to a Cobra® Power Consumption • For each piece of equipment you will be operating from the inverter, you must determine the battery’s reserve capacity (how long the battery can deliver a specific amount of current – in automotive batteries, usually 25 amperes) or ampere-hour capacity (a measure of how many amperes a battery can deliver for a specified length of time). Example – Reserve capacity: a battery with a reserve capacity of 180 minutes can deliver 25 amperes for 180 minutes before it is completely discharged. Example – Ampere-hour capacity: a battery with an ampere-hour capacity of 100 ampere-hours can deliver 5 amperes for 20 hours before it is completely discharged. To determine the battery ampere-hour capacity you require: 1. Determine how many watts each piece of equipment consumes. This can normally be found on the product label. If only the current draw is given, multiply the current draw by 115 to get the watt consumption. 2. Estimate the time (in hours) that each piece of equipment will be running between battery charging cycles. 3. Calculate the total watt-hours of energy consumption (power x operating time) using the average power consumption and the total estimated running time (in hours). Power x Operating Time = Watt-Hours. 4. Divide the watt-hours by 10 to determine how many power supply’s (12 volt) ampere-hours will be consumed. On/Off Switch to On IntroOperationCustomerAssistanceWarrantyNotesNoticeMain IconsSecondary IconsCautionWarningInstallation On/Off Switch to Off IntroOperationCustomerAssistanceWarrantyNotesNoticeMain IconsSecondary IconsCautionWarningInstallation Laptop 50 watts x 2 hours = 100 watt-hours TV/VCR (up to 25") 115 watts x 3 hours = 345 watt-hours Blender 300 watts x 15 minutes = 75 watt-hours 10273_CPI875_PH2 7/10/07 6:04 PM Page 10 10 Turning Your Inverter On or Off • Be sure to have your power inverter properly installed before attempting to turn the unit...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories