Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Correct AWG wire size is determined by the current requirement plus cable length. Please see the IMS Driver to Motor Cable AWG Table in this Appendix. Example A - Cabling Under 50 Feet, IMS Driver to Motor Shield to Earth Ground on Supply End Only Two Shielded/Twisted Pairs (Wire Size from IMS Driver to Motor Cable AWG Table) Braided Shield Ferrite Beads Cable Length less than 50 Feet Phase A Phase A Phase B Phase B Phase A Phase A Phase B Phase B 24 Example B - Cabling 50 Feet or Greater, IMS Driver to Motor Shield to Earth Ground on Supply End Only Braided Shield Ferrite Beads Cable Length 50 Feet or greater Phase A Phase A Phase B Phase B Phase A Phase A *L . 0.5 MH * 0.5 MH is a typical starting point for the Common Mode Line Filters. By increasing or decreasing the value of L you can set the drain current to a minimum to meet your requirements. Phase B Phase B Common Mode Line Filters (2x) Two Shielded/Twisted Pairs (Wire Size from IMS Driver to Motor Cable AWG Table) 25 IMS Driver to Motor Cable AWG Table 1 Ampere (Peak) 5 Amperes (Peak) Length (Feet) 10 25 50* 75* 100* Length (Feet) 10 25 50* 75* 100* Minimum AWG 20 20 18 18 16 Minimum AWG 16 16 14 12 12 2 Amperes (Peak) 6 Amperes (Peak) Length (Feet) 10 25 50* 75* 100* Length (Feet) 10 25 50* 75* 100* Minimum AWG 20 18 16 14 14 Minimum AWG 14 14 14 12 12 3 Amperes (Peak) 7 Amperes (Peak) Length (Feet) 10 25 50* 75* 100* Length (Feet) 10 25 50* 75* 100* Minimum AWG 18 16 14 12 12 Minimum AWG 12 12 12 12 12 4 Amperes (Peak) * Use the alternate method illustrated in Example B when cable length is . 50 feet. Length (Feet) 10 25 50* 75* 100* Minimum AWG 18 16 14 12 12 Driver to Motor Supply Cable Wire Size NOTE:These recommendations will provide optimal protection against EMI and RFI. The actual cable type, wire gauge, shield type and filtering devices used are dependent on the customer’s application and system. NOTE: Always use Shielded/Twisted Pairs for the IMS Driver DC Supply Cable, the AC Supply Cable and the IMS Driver to Motor Cable. 26 WARRANTY TWENTY-FOUR (24) MONTH LIMITED WARRANTY Intelligent Motion Systems, Inc. (“IMS”), warrants only to the purchaser of the Product from IMS (the “Customer”) that the product purchased from IMS (the “Product”) will be free from defects in materials and workmanship under the normal use and service for which the Product was designed for a period of 24 months from the date of purchase of the Product by the Customer. Customer’s exclusive remedy under this Limited Warranty shall be the repair or replacement, at Company’s sole option, of the Product, or any part of the Product, determined by IMS to be defective. In order to exercise its warranty rights, Customer must notify Company in accordance with the instructions described under the heading “Obtaining Warranty Service.” This Limited Warranty does not extend to any Product damaged by reason of alteration, accident, abuse, neglect or misuse or improper or inadequate handling; improper or inadequate wiring utilized or installed in connection with the Product; installation, operation or use of the Product not made in strict accordance with the specifications and written instructions provided by IMS; use of the Product for any purpose other than those for which it was designed; ordinary wear and tear; disasters or Acts of God; unauthorized attachments, alterations or modifications to the Product; the misuse or failure of any item or equipment connected to the Product not supplied by IMS; improper maintenance or repair of the Product; or any other reason or event not caused by IMS. IMS HEREBY DISCLAIMS ALL OTHER WARRANTIES, WHETHER WRITTEN OR ORAL, EXPRESS OR IMPLIED BY LAW OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. CUSTOMER’S SOLE REMEDY FOR ANY DEFECTIVE PRODUCT WILL BE AS STATED ABOVE, AND IN NO EVENT WILL THE IMS BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, SPECIAL OR INDIRECT DAMAGES IN CONNECTION WITH THE PRODUCT. This Limited Warranty shall be void if the Customer fails to comply with all of the terms set forth in this Limited Warranty. This Limited Warranty is the sole warranty offered by IMS with respect to the Product. IMS does not assume any other liability in connection with the sale of the Product. No representative of IMS is authorized to extend this Limited Warranty or to change it in any manner whatsoever. No warranty applies to any party other than the original Customer. IMS and its directors, officers, employees, subsidiaries and affiliates shall not be liable for any damages arising from any loss of equipment, loss or distortion of data, loss of time, loss or destruction of software or other property, loss of production or profits, overhead costs, claims of third parties, labor or materials, penalties or liquidated damages or punitive damages, whatsoever, whether based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory, or other los...
Ce manuel est également adapté pour les modèles :Machines à souder - IM1007 I/IE (584.25 kb)