Handles flux-cored welds on mild steel with ease. Practically everything you need to MIG weld mild steel is right in the box. Unit includes: • 4-Step Tap voltage control • Magnum® 100L welding gun and 10ft. (3m) cable assembly, with gas nozzle, .023” - .035” (0.6–0.9mm) cable liner and .023/.025” (0.6mm) contact tip • 10ft. work cable & work clamp • 6 ft input power cord with NEMA Type 5-15P plug • Guide tubes and reversible drive roll for .023-.035" solid MIG wire and .035" Innershield® flux-co

The AC-225C can be used for many welding applications such as maintenance repairs, fabrication, modifying equipment, and creating or rebuilding tools, fixtures, or worn parts. Features: • Easy Installation • Input power cable and plug included Easy to Operate • Electrode holder and cable, work clamp and cable, sample electrodes, welding helmet and welder's guidebook all included • Easy to use controls •Convenient size to allow easy storage and handling • 3 year warranty including parts and labor

Slide the guide tube up against the installed drive roll. 9. Install the second drive roll on the remaining shaft the same way as the first. Center the middle guide tube between the rolls and tighten the thumbscrews holding it in place. 10. Close and latch both quick release levers. 11. Slide the longer guide tube into the rear hole of the gearbox until it almost touches the drive roll and guide tube. Tighten the thumbscrew to hold it in place. 12. Install the outgoing guide tube into the front

When set on Max., the electrode feeds at more than 500” per minute and the welding current is high. If the power source is equipped with meters, the welding current can be read directly on the ammeter while welding. If the power source has no meters and the relationship between current and wire feed speed is known, current can be accurately set by measuring the wire feed speed. To measure wire feed speed disconnect the electrode cable at the power source: 1. Press the gun trigger and feed ele

and thoughtful operation on your part. DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly, think before you act and be careful. (button) (Stamp comment Rita Wood 07.06.2002 16:27:39 blank) R OPERATOR’S MANUAL World's Leader in Welding and Cutting Products Premier Manufacturer of Industrial Motors • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. T

Specifications and availability of optional features may have changed. Shipping Damage Claims When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, claims for material damaged in shipment must be made by the purchaser against the transportation company at the time the shipment is received. Safety Depends On You Lincoln arc welding equipment is designed and built with safety in mind. However, your overall safety can be increased by proper ins

Features: • Easy Installation • Input power cable and plug included Easy to Operate • Electrode holder and cable, work clamp and cable, sample electrodes, welding helmet and welder's guidebook all included • Easy to use controls •Convenient size to allow easy storage and handling • 3 year warranty including parts and labor • Output: 170 amps, 25 volts, 20% duty cycle • Amp Range: 40-225 • Size: 15.2”h X 14”w X 13.5”d • Weight: 86 lbs. • CSA approved • UL listed • Powder Paint Finish for increase

After the battery is charged, reconnect the positive battery cable first and the negative cable last. Failure to do so can result in damage to the internal charger components. Follow the instructions of the battery charger manufacturer for proper charger settings and charging time. SERVICING MUFFLER WITH INTERNAL SPARK ARRESTOR Clean every 100 hours. Remove screw plug on muffler body and either vacuum out OR shake out until clean. WARNING • MUFFLER MAY bE HOT • ALLOW ENGINE TO COOL bEFORE INSTAL

Specifications and availability of optional features may have changed. THE LINCOLN ELECTRIC COMPANY The World's Largest Manufacturer of Arc Welding Equipment Cleveland 17, Ohio CONTROL PANEL 1 Rheostat 2 Rheostat Handle 3 Diverter Switch Blade & Handle 4 Diverter Switch Receptacle, 4th step 5 Diverter Switch Receptacle, 3rd step 6 Diverter Switch Receptacle, 2nd step 3,4, 5, 6 Diverter Switch Complete 7 Voltameter 8 Voltameter Switch 9 Voltameter Shunt 10 Push Button 11 Wing Nuts

Section III - Hazardous Ingredients (1) I M P O R T A N T ! This section covers the materials from which this product is manufactured. The fumes and gases produced during welding with the normal use of this product are covered by Section VII; see it for industrial hygiene information. CAS Number shown is representative for the ingredients listed. (1) The term “hazardous” in “Hazardous Ingredients” should be interpreted as a term required and defined in the Hazardous Products Act and does not nec