Évaluations - 4, GPA: 4
(
)
)
|
Photos et spécifications Hyundai H-LCD3202 |
Facilité d'utilisation
(in VGA source). Manual config.: Press UP/DOWN buttons to select Manual config., press RIGHT button to enter, and press UP/DOWN buttons to select Phase, Clock, H.Position. Press LEFT/RIGHT buttons to adjust (in VGA source). VGA/XGA mode: Press UP/DOWN buttons to select VGA/XGA mode, press RIGHT button to enter, and press UP/DOWN buttons to select the definition (in VGA source). Aspect: Press UP/DOWN buttons to select Aspect, press RIGHT button to enter, and press UP/DOWN buttons to select the ratio of the screen. Noise Reduction: Press UP/DOWN buttons to select Noise Reduction, press LEFT/RIGHT buttons to turn on/off the noise reduction function. H/V Position: Press UP/DOWN buttons to select H/V Position, press LEFT/RIGHT buttons to adjust the picture position. Press ENTER button to confirm and return to preview menu. SOURCE Menu Press MENU button to display the OSD menu, press UP/DOWN buttons to select Source menu. Press RIGHT button to enter the menu. Press MENU button to return to the main menu, or press RIGHT button to enter the submenu. MP Input: Press UP/DOWN buttons to select MP Input, press RIGHT button to enter, press UP/DOWN buttons to select the input source. Press ENTER button to confirm. PIP function Press UP/DOWN buttons to select “PIP”, press RIGHT button to enter the submenu. When you select “On”, and press ENTER button to confirm, the “PIP Input” and “Win. position” menu will be displayed. MP Input: When you turn on the PIP function, you can select only four input sources for the main picture: YPbPr, VGA, HDMI1, HDMI2. PIP input: Select the PIP input source, you can select four sources here: TV, AV, SCART1, SCART2. Win. position: Select the PIP picture’s position. ^‘ SEARCH HP Input PICTURE * TV AV SCART1 SOUND SCART2 S-Vkteo TIMER YPbPr VGA • ( SETUP HDMI1 HDMI2 -TP- SCREEN Ml 1 c i-Li ten— e ■■ 1 SOURCE Menu Prw I s ^m pt | PCTUC On X SOIM *Ot1 "44 sm* SO» IN I" I*“« I 13 Troubleshooting Before calling a technician, please check the following items to see whether you can easily diagnose and fix the encountered symptoms on your own. Symptoms Possible Cause Correction No picture, no sound, and no indicator light The power cord is not plugged in. Contrast, brightness, sharpness, color and volume are all in the minimum value or TV is in mute mode. Plug the power cord in. Alter the value of contrast, brightness, sharpness, color and volume. Picture and sound with abnormity Contrast and color are set improperly. Color system is set improperly. Sound system is set improperly. Set the value of Contrast and color properly. Set the sound system properly. Picture is spotted or with snow Signal source is low-grade or the signal is in a lower quality. Use the qualified signal cord. Blue background No video signal or the signal cord is improperly/not connected. Connect the signal cord properly. PC Picture is not in the middle of the screen Picture is not well adjusted. Press the CH+/CH- buttons at one time to adjust it. Adjust H/V- position manually to adjust it. No sound No audio signal or the signal cord is improperly/not connected. Connect the audio signal cord properly. Set the sound system properly. The RC does not work Batteries are improperly installed or exhausted. Make sure the positive and the negative polarities are correct. Reattach the battery lid. Replace the batteries. The causes of interference Incorporated in your TV receiver are the most up-to-date devices to eliminate interference. Local radiation however, can create disturbances, which visibly affect your picture. Proper installations, a good aerial are your best safeguards against these disturbances. • RF INTERFERENCE Moving ripples across the screen are caused by nearby transmitting or receiving short-wave radio equipment. • DIATHERMY Herringbone pattern and partial picture loss can result from the operation of diathermy equipment from a nearby doctor's surgery or hospital. • SNOW Weak TV signals from long distant stations result in an instead picture and give the effect of falling snow. An antenna adjustment or antenna amplifier may be needed. • GHOST Multiple image, caused by TV signals reflected back from surrounding buildings, hills, aircraft, etc. is minimized by correct aerial positioning. • CAR IGNITION Nearby cars and electrical motors can cause small streaks across the picture or make the picture roll. 14 Specifications Items H-LCD3202 LCD panel items Size (diagonal) 32” (81 cm) Brightness 500 (cd/m2) Contrast 2000:1 Angle of view 170°/170° High speed response 8 ms Resolution 1366x768 Aspect ratio 16:9 Color system PAL, SECAM Sound system DK, I, BG NICAM Stereo 2 x 6 W S-video in Yes SCART 2 lines Component (YPbPr) input Yes PC audio input Yes VGA Yes HDMI input 2 lines Plug and Play Yes Russian OSD Yes Progressive scan Yes Digital comb filter Yes Timer on/off Yes PIP Yes Quantity of channels 200 Tele...