Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Normally, set this to "Auto". Note • "Audio Input Fix" is not selectable when PIP is on. Menu Adjustment 29 Additional Information ■ Connecting the 3D WOOFER You can enjoy high quality sound by connecting the 3D WOOFER as follows: • Connect only the supplied 3D WOOFER; otherwise your TV may malfunction. • Unplug your TV from the wall outlet when connecting the 3D WOOFER. • Toprevent a malfunction caused by a short circuit of the terminals, make sure that none of the 3D WOOFER wire strands stick out, making contact with the neighbouring 3D WOOFER terminal. ■ Connecting optional components Connecting to the video input terminal ( t ) TV rear panel 5QUCS> Antenna cable (not supplied) ----^ Audio/Video cable k(not supplied) S Video cable (not supplied) VCR Notes • If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the program number 0 on the TV (see page 27). • When both -© (S video) and © (video) for t1 or t4 are connected at the same time, -Q (S video) is automatically selected. To view (A) (video), disconnect the S video cable. Connecting to the monitor output terminal ( T ) TV rear panel continue Additional Information 31 continued Connecting to the component video input terminal ( -O ) Notes • If your DVD player can output interlace and progressive mode signals, select the interlace output when connecting to (component video input) on your TV. Your TV can receive either 525i/60Hz or 625i/50Hz interlace signals. • Some DVD player terminals may be labeled differently: Connect To (on the DVD player) Y (green) Y Cb (blue) Cb, Pb, Cb or B-Y Cr (red) Cr, Pr, Cr or R-Y • If you select "DVD" on your TV screen, the signal from the (monitor output) jacks will not be output properly. This does not indicate a malfunction. 32 Additional Information ■ Troubleshooting If you find any problem while viewing your TV, you can either use the Reset function or check the Troubleshooting guide below. If the problem persists, contact your Sony dealer. RESET f© ®^TT OPTION RESET 99 08 (O » O O') Reset function Press the RESET button on your remote control. Your TV will go blank for a few seconds, then the "Initial Setup” menu will appear. Pressing RESET will set your TV to the factory setting, but certain problems may be solved. Troubleshooting guide Possible cause Solutions • The connection is loose or the cable is damaged. • Check the antenna cable and connection on the TV, VCR and at the wall. • The antenna setup is inappropriate. • Check the antenna setup. Contact a Sony dealer for advice. • Channel presetting is inappropriate or incomplete. • Display the "Channel Setup” menu and select "Manual Program” to preset the channel again. • Signal transmission is low. • Display the "Channel Setup” menu and set the "Signal Booster” to "Auto” from "Manual Program”. • Try using an external booster. • Broadcast signals are too strong. • Turn off or disconnect the external booster if it is in use. • Display the "Channel Setup” menu and set the "Signal Booster” to "Off” from "Manual Program”. • The TV system setting is inappropriate. • Display the "Channel Setup” menu and select the appropriate "TV System” from "Manual Program”. • PIP sound is selected when PIP is displayed. • Press O or C5. Symptom Page Snowy picture Noisy sound US 30 27 27 Distorted picture Noisy sound in 27 Good picture Noisy sound US 27 13 continue Additional Information 33 continued Symptom Possible cause Solutions Page No picture No sound mx • The power cord, antenna or VCR is not connected. • Check the power cord, antenna and VCR connections. 30 • The TV is not turned on. • Press 1/1 (power). • Press ® (main power) on the TV to turn off the TV for about five seconds, then turn it on again. 10 9 No sound or inappropriate sound • The "Party Mode Setup” is functioning. • Display the "Setup” menu and set the "Audio Input Fix to "Off” from "Party Mode Setup”. 28 Good picture No sound OflX • The volume level is too low. • Press 2 + to increase the volume level. 10 • The sound is muted. • Press d3< to cancel the muting. 10 • PIP sound is selected when PIP is displayed. • Press ® or 0. 13 Dotted lines or stripes • There is local interference from cars, neon signs, hair dryers, power generators, etc. • Do not use a hair dryer or other equipment near the TV. • Check the antenna setup. Contact a Sony dealer for advice. - Double images “ghosts” r • Broadcast signals are reflected by nearby mountains or buildings. • Use a highly directional antenna. • Use the fine tuning ("Fine”) function. 27 • The antenna setup is inappropriate. • Check the antenna setup. Contact a Sony dealer for advice. - • Use of an external booster is inappropriate. • Turn off or disconnect the external booster if it is in use. - No color • The color level setting is too low. • Display the "Picture” menu and select "Personal” of "Mode”, then adjust the "Color” level in "Pictu...
Ce manuel est également adapté pour les modèles :TV - KV-SR29M99K (1.71 mb)