Évaluations - 2, GPA: 4 ( )

Fabricant : Samsung Taille : 10.15 mb Nom Fichier : Langue d'enseignement:

The values of fine, coarse and position are adjusted automatically. Easy Setting 1. Press the TOOLS button on the remote control. 2. Press the ▲ or ▼ button to select “Auto Adjustment”, then press the ENTERS button. ♦ Screen Adjustment: Coarse/Fine The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by Fine-tuning alone, then adjust the frequency as best as possible (coarse) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned on the center of screen. Press the ▲ or ▼ button to select "Coarse" or "Fine", then press the ENTERS button. Press the ◄ or ► button to adjust the screen quality. Press the ENTERS button. Position Adjust the PC's screen positioning if it does not fit the TV screen. Press the ▲ or ▼ button to adjusting the Vertical-Position. Press the ◄ or ► button to adjust the Horizontal-Position. Press the ENTERS button. Image Reset You can replace all image settings with the factory default values. C ___ ^ Move S1 Enter 'O Return English - 30 What is Anynet+? Anynet+ is an AV network system that enables an easy-to-use AV interface for users by controlling all connected AV devices through the Anynet+ menu when Samsung Electronics AV devices are connected. Connecting Anynet+ Devices_ The Anynet+ system supports AV devices supporting Anynet+ only. Check if there is an Anynet+ mark on the AV device to be connected to the TV. To directly connect to TV Connect the [HDMI 1], [HDMI 2] or [HDMI 3] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using the HDMI cable. To connect to Home Theater 1. Connect the [HDMI 1], [HDMI 2] or [HDMI 3] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using the HDMI cable. 2. Connect the HDMI IN jack of the home theatre and the HDMI OUT jack of the corresponding Anynet+ device using the HDMI cable. ^ Connect only one receiver. ^ You can connect an Anynet+ device using the HDMI cable. Some HDMI cables may not support Anynet+ functions. ^ Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status. ^ Anynet+ supports up to 8 AV devices in total. English - 31 Setting Up Anynet+ I Anynet+ (HDMI-CEC) Picture Mode Standard Sound Mode Custom Sleep Timer Off SRS TS XT Off Energy Saving Off Dual l-ll Mono ^ Move 0Enter 5 Exit TV P9 View TV Select Device > Record > 1 Menu on Device > — Device Operation > '■, Receiver :Off > ^ Setup > ^ Move 0Enter *3 Return Setup Anynet+ (HDMI-CEC) Off Auto Turn Off : m Searching Connections ± Move O'Enter 'D Return The following settings are to use Anynet+ functions. Using the Anynet+ Function 1. Press The TOOLS button. Then Press the ENTERS' button to select "Anynet+(HDMI-CEC)". Press the ▲ or ▼ button to select "Setup", then press the ENTERS button. 2. Press the ENTERS button to select "Anynet+ (HDMI-CEC)", then press the ENTERS button. 3. Press the ▲ or ▼ button to select "On", then press the ENTERS button. ^ The "Anynet+ (HDMI-CEC)" function is enabled. ^ If you select "Off', "Anynet+ (HDMI-CEC)" is disabled. ^ When the "Anynet+ (HDMI-CEC)" function is disabled, all the Anynet+ related operations are deactivated. Turning an Anynet+ Device Off Automatically when the TV is Turned Off 1. Press the ▲ or ▼ button to select "Auto Turn Off", then press the ENTERS button. 2. Press the ▲ or ▼ button to select "Yes", then press the ENTERS button. ^ The Auto turn off function is enabled. ^ If you select "No", the Auto turn off function is cancelled. Press the EXIT button to exit. ^ The Select Device setting of the TV remote control is to be set to TV to use the Anynet+ function. ^ If you set "Auto Turn Off" to "No", connected external devices are also turned off when the TV is turned off. However, if the device is recording, it may not be turned off. Setup Anynet+ (HDMI-CEC) : On Auto Turn Off : No Searching Connections | Yes English - 32 Scanning and Switching between Anynet+ Devices 1. Press the TOOLS button. Then press the ENTERS' button to select "Anynet+(HDMI-CEC)". 2. Press the ▲ or ▼ button to select "Select Device", then press the ENTERS button. 3. Press the ▲ or ▼ button to select to a particular device and press the ENTERS button. It is switched to the selected device. 4. If you cannot find a device you want, press the ▲ or ▼ button to select "Setup", then press the ENTERS button. 5. Press the A or T button to select "Searching Connections", then press the ENTERS button. The message "Configuring Anynet+ connection..." is displayed. When searching devices completes, the connected devices are listed in the Anynet+ menu. ^ Switching to the selected devices may take up to 2 minutes. You cannot cancel the operation during the switching operation. ^ The time required to scan for devices is determined by the number of connected devices. ^ When the device scan is complete, the number of found de...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :