Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
Move the slide switch at the top of the remote to the position for the product you want to control. Refer to the table below. Only one of each device type can be controlled in each slide-switch position. Switch Position Affected Device CABLE/SAT Cable Box DTV Receiver Satellite Receiver VCR VCR DVR Laser Disc Player DVD Player/Recorder DVD DVD Player/Recorder DVR Laser Disc Player VCR AUDIO A/V Receiver Audio Amplifier CD Player* 2. Press and hold POWER on the remote control for several seconds until the button blinks twice and goes off. 3. Release the POWER button. 4. Enter the first five-digit code listed for your equipment. • The POWER button blinks twice when you start to enter the code and then once for each additional keypress. • The POWER button blinks twice when you finish entering a valid code. • Move the slide switch to another position if you need to start over or wish to exit programming mode. 5. Point the remote control at the equipment and press POWER. If the product has no power on/off function, press a different key, such as (PLAY), (STOP), VOL , or MUTE. • If the equipment responds, the remote control is properly programmed to operate the equipment. • If the equipment does not respond, repeat steps 2–4 with the next five-digit code listed for your equipment. 6. Once you have found the correct code, write it in the space below for future reference. Switch Position Device Type Code CABLE/SAT VCR DVD AUDIO Method 2: Code Search In this method of programming, you step through the remote control’s internal code library to find the correct code for your A/V product. 1. Move the slide switch at the top of the remote control to the correct position for the product. See the table under “Method 1.” 2. Press and hold POWER on the remote control for several seconds until the button blinks twice and goes off. 3. Press keys 9 9 1 4. Press the number 1, 2, or 3 depending on the slide- switch position and the table below. Switch Position Number CABLE/SAT 1 DVD, VCR 2 AUDIO 3 5. Press CH and POWER repeatedly until the product responds by powering on or off. You can press CH to move backward through the code library if needed. NOTE: If the product has no power on/off function, check for a response using a different function. Press (PLAY), (STOP), VOL , or MUTE and then repeatedly press CH / to check for a response. 6. When the product responds, press ENTER to set the code. Code Verification To determine the code programmed for any position of the slide switch: 1. Move the slide switch to the position you wish to verify. 2. Press and hold POWER on the remote control for several seconds until the button blinks twice and goes off. 3. Press keys 9 9 0 IMPORTANT You may need to reprogram the remote control after changing the batteries. 4. Press 1 and count the blinks of the power button. Write down the number of blinks as the first digit of the code. 5. Repeat step 4 for the second, third, fourth, and fifth digits of the code. Appendices 103 Appendix D: Programming the Remote Control Programming Codes Audio Lock: Universal A/V Receiver Control With Audio Lock active, the remote control operates the volume and mute functions of the A/V receiver in all positions of the slide switch. Activate Audio Lock if you normally use an A/V receiver with your TV and other A/V equipment. 1. Program the AUDIO position for your A/V receiver as described earlier in this section. 2. Move the slide switch to the AUDIO position. 3. Press and hold POWER on the remote control for several seconds until the button blinks twice and goes off. 4. Press keys 9 9 3 ENTER The POWER button will blink twice to indicate Audio Lock is active. To Reset the Remote Control to Operate Volume and Mute for the TV Speakers 1. Press and hold POWER for several seconds until the button blinks twice and goes off. 2. Press keys 9 9 3 VOL . The POWER button will blink four times to indicate Audio Lock has cleared. Resetting the Remote Control If the slide switch is set to TV and the TV does not respond properly, do the following to reset the remote control. 1. Press and hold POWER for several seconds until the button blinks twice and goes off. 2. Release the POWER button. 3. Press keys 0 0 9 3 5 and the POWER button will blink twice when you finish entering the code. While entering the code, pause for a moment between each key press to ensure it is recognized. Audio Amplifiers Brand Code Acurus 30765 Adcom 31100, 30577 Altec Lansing 31742 Aragon 30765 Bel Canto Design 31583 Bose 30674 Carver 30892 Classe 31462, 31461 Curtis Mathes 30300 Durabrand 31561 Elan 30647 GE 30078 Harman/Kardon 30892 JVC 30331 Klipsch 30765 Left Coast 30892 Lenoxx 31561 Lexicon 31802 Logitech 31408 Marantz 30892 Mark Levinson 31483 McIntosh 30251 Mondial 30765 Optimus 30823, 30395, 30300 Philips 30892 Pioneer 30823, 30300, 30257, 30013 Polk Audio 30892 RCA 30823, 30300 Realistic 30395 Sharp 30226 Sony 30815 Soundesign 30078 Technics 30374, 30372 Toshiba 30353 Victor 30331 Wards 30078, ...