Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Do I need to change the playback speed when playing back LP recordings? During playback, the correct speed will automatically be selected. For more information, please read the section 'Selecting the recording speed (SP or LP)' in the chapter 'Manual recording'. Playing back NTSC cassettes Cassettes that have been recorded in the NTSC standard (for example, American cassettes) can be played back using this TV-Video Combi. Searching for a tape position with picture (scanning) 1. 1.1.While a cassette is playing, press s0 (reverse) or B1 (forward) one or more times. 2. 2.2.Press KB to resume playback. Still picture 1. 1.1.During playback, press STILL 2 to stop the tape and display a still picture. 2. 2.2.To continue playback, press KB . Scanning and still motion interferes with the picture quality. The sound is switched off. This is not a fault in your TV-Video Combi. Searching for tape position without picture (forward wind and rewind) 1. 1.1.Stop the tape with LC . 2. 2.2.Press s0 (reverse) or B1 (forward). 3. 3.3.To stop the tape, press LC . Manual Tracking To adjust the tracking manually, press P+ or P-on the TV/VCR during playback. Tracking returns to Automatic Tracking Adjustment when you press LC or insert a tape. EN 10 6. Manual recording General information Use 'Manual Recording' to make a spontaneous recording (for example, a programme currently being shown). If you want to start and stop a recording manually, read the section 'Recording without automatic switch-off'. If you want to start a recording manually but have it stopped automatically, read the section 'Recording with automatic switch-off'.(e.g. not to record to the end of the tape) Read the section 'Automatic recording from a satellite receiver', if you want a recording to be controlled automatically by a satellite receiver. Recording without automatic switch-off 1. 1.1.Insert a cassette. 2. 2.2.Use P+ P- or 0..9 to select the programme number you want to record, for example, 'P01'. 3. 3.3.To start recording, press RECORD/OTR I . 4. 4.4.To stop recording, press LC . Recording with automatic switch-off (OTR One-Touch-Recording) 1. 1.1.Insert a cassette. 2. 2.2.Use P+ P- or 0..9 to select the programme number you want to record. 3. 3.3.Press RECORD/OTR I . 4. 4.4.Each time you press RECORD/OTR I you will add 30 minutes to the recording time. Preventing accidental erasing of cassettes All cassettes (except for rental and pre-recorded purchased cassettes) have a security tab on the back of the cassette. To prevent recording over important recordings (erasing), you can remove this security tab. If you later decide to record on a protected cassette, simply cover the hole with adhesive tape. Lining up recordings (assemble cut) When you add a further recording to a cassette, which already has a recording on it, a short blank (flicker) can appear between the old and the new recording or the picture itself can flicker. To help reduce these from occurring, proceed as follows: 1. 1.1.Find the tape position of the old recording where you want to insert the new recording. 2. 2.2.Look at the last minute of the old recording (playback). 3. 3.3.Press STILL 2 22 at the tape position where the new recording is to go and press RECORD/OTR I . 4. 4.4.Now start recording as usual by pressing RECORD/OTR I on the remote control. 5. 5.5.Stop recording with LC . Selecting the recording speed (SP or LP) LP allows to double the recording duration on tape (for example six hours instead of three hours on a E180 cassette). 1. 1.1.Press MENU . The main menu will appear. 2. 2.2.Select 'RECORD SETUP' with KB LC and confirm with B1 . SELECT KL CHOOSE B >RECORD SPEED [SP] END=EXIT 3. 3.3.Select the required recording speed with B1 . 4. 4.4.To end, press STATUS/EXIT . 'SP'/'LP' 'SP': StandardPlay (normal recording speed) offers the usual first-class picture quality. 'LP': LongPlay (half recording speed, double recording time). 6 hours can be recorded on a 3hour cassette (E180) with a somewhat reduced picture quality. 11 EN 7. Programming a recording (TIMER) General information Use a TIMER programming to automatically start and stop a recording at a later time or date. The TV-Video Combi will switch to the right programme number and begin recording at the correct time. With this TV-Video Combi, you can pre- programme up to eight recordings within a period of one year. To make a programmed recording, your TV-Video Combi needs to know: *the date you want to make the recording *the programme number of the TV channel *the start and stop time of the recording *PDC on or off (14PV203/07, 14PV460/07) This information is saved in a TIMER block. <14PV203/07, 14PV460/07> What is 'PDC'? 'PDC' (Programme Delivery Control) is used to control the start and duration of TV channel recordings. If a TV programme starts earlier or ends later than scheduled, the TV-Video Combi will turn on and off at the correct time. What do I need to know about 'PDC'? Usually the PDC time is the same as the start ...
Ce manuel est également adapté pour les modèles :TV - 14PV203/07 (186.62 kb)