Évaluations - 5, GPA: 4
(
)
)
|
Facilité d'utilisation
If you take a few minutes to look through it, you’ll learn how to use all of the features of your new Jensen antenna for maximum enjoyment. Contents Precautions………………………………………………………………………………………….….1 Preparation…………………………………………………………………………………………..….1 Installation………………………………………………………………………………………...…1-4 Operation………………………………………………………………………………………….……5 Specifications…………………………………………………………………………………………..5 System Layout………………………………………………………………………………………….6 Troubleshooting………………………………………………………………………………………...7 PRECAUTIONS • Proper Power Supply This product is designed to operate with a 12 volt DC, negative ground power system • Use Authorized Service Centers Do not attempt to disassemble or adjust this precision product. Contact a professional for service • Do not install couplers or splitters between the wall plate and antenna Installation of any item on this cable lead may cause a short. This cable provides power to the Antenna preamp. • Power Supply should disconnected during installation Connect all coax cable connections before connecting +12VDC wire to the wall plate. The switch should be in the OFF position when connecting/disconnecting cables. • All coaxial cable used should be RG-6U for optimal performance • Painting the Antenna is not recommended and may affect performance • Do not use solvents to clean antenna. Use only mild soap and water. PREPARATION Please read all instructions before beginning the installation. Tools and Supplies • Drill or Battery Driver with a #2 Phillips Bit • .” Drill Bit • Caulking Gun • Tube of Approved Exterior Roof Caulk • RG-6U Coaxial Cable • 16AWG Power & Ground Wire ANTENNA INSTALLATION 1. Remove all packaging contents from shipping box. 2. Locate the Antenna Housing 3. Determine a suitable location to mount the antenna. This location should allow for approximately 24” of clearance around the antenna. Avoid close proximity to other roof mounted objects (AC, Vents, & Roof Edges). See Figure 1 below. ROOF VIEW AC 24" VENT NOTE: ANTENNA SHOULD BE MOUNTED AS CLOSE TO THE CENTER OF THE ROOF AS POSSIBLE FOR BEST R E C E P TIO N . THE ANTENNA SHOULD NOT BE LOCATED WITHIN 24" OF ANY OBJECT OR ROOF EDGE. FIGURE 1 2 3 ANTENNA INSTALLATION 4. Remove metal base from plastic housing by removing the lock screw and sliding the base away from the plastic stalk. Mark hole locations on roof. Drill 5/8” hole for the coax cable. Pre-drill the 3 mounting screws holes with a 1/8” bit. Route RG6 Coax from wall plate through hole. See Figures 2, 3, & 4. FIGURE 2 ANTENNA LOCK SCREW MOUNTING BASE 5. Apply approved caulking compound around all holes. Place base over holes and caulking. Secure base using the included 3 screws. Apply approved caulking compound to screw heads and fill .” hole with caulking compound. See Figure 4 6. Connect the 2 coax cables ensuring the fitting is snug (Do Not Over tighten). Reinstall the plastic housing onto the base. Reinstall the lock screw. 7. Additional caulking compound may be applied to the outside seam of the base. Please note there is a moisture weep hole at the rear of the base. If proper sealing techniques are used (as described in Step 5) you should not need to add additional caulking around the base. NOTE: The Caulking compound used should be approved for the type of vehicle and environment. Check OEM recommendations for your vehicle. Material should be a non-hardening type such as Butyl caulking. FRONT OF VEHICLE CENTER LINE OF ROOF DRILL 5/8" HOLE APPLY APPROVED CAULKING COMPOUND AROUND THE 4 HOLES FIGURE 3 3 - 1/4"x14 SCREWS (INCLUDED) MOUNTING BASE A P P L Y A P P R O V E D C A U L K I N G C O M P O U N D 4 P L A C E S F IG U R E 4 4 WALL PLATE INSTALLATION 1. The wall plate/power supply assembly may be mounted in most electrical outlet/switch boxes. The plate can also be mounted without an electrical box. This mounting method requires a hole 2.75” x 2.0”. Route 2 16AWG wires to this hole from the 12VDC source. Also route all coax cables to this hole. See Figure 5. 2. Connect all coax cables to the appropriate wall plate pigtails. Each pigtail has a label for identification. Connect the cable from the roof antenna to the “ANTENNA IN”. Connect the “TV2 OUT to TV input. “RADIO OUT” goes to the input of the AM/FM radio. “CABLE IN” connects to the Park Cable Input. See Figure 6. (Do Not Over tighten) 3. After connecting all coax cables, connect +12VDC wire to the + male spade terminal on the circuit board (marked with a red dot) using a .” Insulated Female Spade Terminal. Then connect the ground wire (marked with a black dot) using the same type terminal. See Figure 6. 6. Install the wall plate using a two #6 Flat Head screws. 7. Connect main TV to the TV1 output on the front of the wall plate. 2.0" 2.75" INTERIOR WALL ROUTE ALL POWER/GROUND WIRES AND COAX CABLES THROUGH THIS HOLE FIGURE 5 * Recommendation of RG-6U cable type with a maximum length of 10 feet between Plate and Antenna. ANTENNA IN TV2 OUT RADIO OUT CABLE IN To Park Cable To AM/FM Radio To Ant...