Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
1)The supplied indoor antenna is adequate when your vehicle is stationary. For best reception on the road, use a high-quality VHF/UHF mobile TV antenna. 2)Attach the car battery cord to the DC13.2V connector on the back of the TV/VCR. Then, connect the other end to your vehicle's cigarette-lighter socket. NOTES: • Be sure your vehicle has a 13.2-volt, negative- ground electrical system. • Be sure you use only the supplied car battery cord. Using another cord could damage the TV/VCR. • Be sure the socket is free of ashes and other debris. • Be sure to push the car battery cord’s plug completely into the cigarette-lighter socket. • Always unplug the car battery from the cigarette- lighter socket before you unplug it from the TV/VCR. • You must disconnect the car battery cord from the TV/VCR before you can use the AC power. • Be sure to replace the fuse with only the same type, 5A, 250V. • Do not touch the metal parts of plug immediately after a car battery cord is disconnected. Because they become hot. EXTERNAL INPUT MODE When using an external input signal (another VCR or video camera), connect the player’s audio/video output cables to the AUDIO IN/ VIDEO IN jacks of your TV/VCR. Then press the CHANNEL K or L button until “AUX” appears on the screen. NOTE: “AUX” is found below the lowest memorized channel. AUX (Example: CH2) INSTALLING THE BATTERIES 1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow. 2)Insert 2 “AA” penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings. 3)Replace the cover. ANT. ANT. AC 120VDC 13.2V VHF/UHF Combination Mobile Antenna (Not supplied) Car battery cord (Supplied) To the vehicle’s cigarette-lighter socket DC13.2V - 10-EN 0B19 SET UP FOR USE You can program the tuner to scan all the channels you receive in your area. NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then select the channel to be viewed on the Cable Box or Satellite Box. CHANNEL SET UP FOR THE FIRST TIME 1 Plug in the TV/VCR power cord Attach the smaller end of the supplied AC cord to the AC 120V connector on the back of the TV/VCR. Then, plug the other end into a standard AC outlet. NOTE: • You must disconnect the car battery cord from the TV/VCR before you use AC power. • If some digits appear in the corner of the screen, press the POWER button without unplugging the power cord. 2 Turn on the TV/VCR Press the POWER button to turn on the TV/VCR 3 Select “ENGLISH” or – SET UP – “ESPANOL” B LANGUAGE [ENGLISH] ESPANOL Select “ENGLISH” or “ESPANOL”=Spanish using the AUTO PRESET F.FWD/B or REW/s button. “[ ]” indicate the selected language. 4 Begin auto preset – SET UP – Press the PLAY/K or STOP/L but- LANGUAGE [ENGLISH] ESPANOL ton to point to “AUTO PRESET”. B AUTO PRESET Then press the F.FWD/B button. The tuner scans and memorizes all active channels in your area. NOTES: • The TV/VCR distinguishes between standard TV channels and cable channels. • If you want to play or record a video tape BEFORE presetting the tuner, you must press the MENU button on the remote control. To preset the tuner again, see “CHANNEL SET UP AGAIN” on page 13. • The TV/VCR may recognize TV channels to be CATV channels by the receiving conditions. In this case, try auto preset again in the fine receiving conditions. 5 After scanning The tuner stops on the lowest memorized channel. If you want to recall the selected channels, you can select the desired channel directly with the remote control number buttons or CHANNEL K or L button. TO SELECT A DESIRED CHANNEL You can select the desires channel by using the CHANNEL K or L button or directly pressing the number buttons on the remote control. Note for using the number buttons: • When selecting cable channels which are higher than 99, press the +100 button first, then, press the last two digts. (Example: to select channel 125, first press the +100 button then press “2” and “5”). • You must proceed single-digit channel numbers with a zero (Example: 02 ... 09). - 11-EN 0B19 CLOCK SET UP (AUTO / MANUAL) Set the clock accurately for proper automatic timer recording. If the Public Broadcasting Station (PBS) is available in your area, follow “AUTO CLOCK SETTING”. If it is not, follow “MANUAL CLOCK SETTING”. AUTO CLOCK SETTING You can have the TV/VCR set the clock automatically by using the Public Broadcasting Station (PBS) channel in your area. Once you have set the clock by using the following procedure, the TV/VCR will automatically monitor the correct time and date being broadcast by the PBS station in your area, using a new service called Extended Data Service (XDS). Make sure ... • TV/VCR power must be turned on. • Confirm that the antenna connections are correct. • The cable converter box must be turned on if your TV/VCR is connected directl...