Évaluations - 3, GPA: 4.3 ( )

Fabricant : Mitsubishi Electronics Taille : 10.02 mb Nom Fichier : Langue d'enseignement:

Front Control Panel for models VS-45609, VS-50609, VS-55609, and VS-60719. INPUT A/V RESET A Ö O Ö o o o CANCEL ADJUST CHANNEL VOL O O QQ O O O MENU ENTER ▼ ▼ POWER Figure 2. Front Control Panel for model VS-70709. IMPORTANT I The Front Button Lock can be disabled from the Front Control Panel by depress ing the MENU button for 8 seconds. When successful, the message “Front Button Lock Disabled” will display on the screen. TIMER I I o or TIMER Timer During normal operation, when the TV is set to turn on at a specific time, the green timer light will blink while the TV is off. Please see Timer, page 37, for timer setup instructions. A/V Reset Press this button to reset the A/V memory on all six inputs to the factory default settings. To reset each input individually, see A/V Memory Reset, page 40. S-VIDEO T or — INPUT-3 VIDEO (MONO) L-AUDIO-R Input 3 This input can be used for convenient connection of a camcorder or other video device to the TV. Please note that if you connect to the S-VIDEO terminal, the VIDEO terminal is deactivated. The VIDEO terminal is active when there is no S-Video connection. S-VIDEO INPUT-3 L-AUDIO-R S-VIDEO 12 Part II: Installation Back Panel CABLE ANT-A LOOP-OUT ANT -B VHF/UHF KOI) (75 OHMS) IR EMITTER HOME THEATER COMPONENT DVD (YPrPb) AUDIO Q S-VIDEO /^\ ir. L (MONO) R TUNER/ MONITOR '¡P' I Î FIXED/ VARIABLE INPUT INPUT OUTPUT 2 ¿1 Antenna (ANT-A, CABLE LOOP-OUT, ANT-B) ANT-A and ANT-B receive signals from VHF/UHF antennas or a cable system. LOOP OUT sends the ANT-A signal out to another component, such as a cable box or VCR. ^ Component Input This input can be used for the connection of A/V equipment with component video outputs, such as a DVD player. Please see Appendix B, page 57, for signal compatibility. y Inputs 1-2 These inputs can be used for the connection of a VCR, Super VHS (S-VHS) VCR, laser disc player, or other A/V device to the TV. Please note that if you connect to the S-VIDEO terminal, the VIDEO terminal is deactivated. The VIDEO terminal is active when there is no S-Video connection. R Output (Tuner/Monitor) The Tuner/Monitor Output sends the TV audio and video signals, excluding component video, to an A/V receiver or other equipment. ^ IR Emitter Home Theater (System 4 Home Theater IR Control) Models VS-601719 and VS-70709 Connecting IR emitters here allows the TV to automatically change a digital A/V receiver’s input in a home theater setup, and pass IR commands to other A/V devices. 13 Back Panel Functions How Connections Affect the PIP Part II: Installation How Connections Affect the PIP To see a picture in the PIP inset, you may need to select an input source. If the only input connected is ANT-A, then both the main picture and the PIP insert will be from that input source. If other video equipment is connected, you may be able to view these input sources as the PIP insert. When connecting your new Mitsubishi bigscreen, it is important to understand which main picture and PIP input sources can and cannot be used together. Table 1 shows which inputs can and cannot be used together and their limitations. To see which input is being displayed as the main picture, press INFO on the TV remote control. To see which input is being displayed as the PIP and for PIP operating instructions, see Operation of PIP, pages 50-51. PIP MAIN^\^ ANT-A ANT-B INPUTS 1-3 COMPONENT INPUT ANT-A OK NO PIP OK NO COMPONENT PIP ANT-B OK OK* OK NO COMPONENT PIP INPUTS 1-3 OK OK OK NO COMPONENT PIP COMPONENT INPUT OK OK OK NO COMPONENT PIP Table 1. How connections affect the PIP. *PIP must be the same channel as MAIN. How Connections Affect the System 4 Home Theater IR Control Models VS-60719 and VS-70709 The Mitsubishi System 4 Home Theater IR Control is a special feature that makes it easier to use your TV with a digital surround sound A/V receiver. Once your equipment is properly connected and set up, your TV and digital A/V receiver will change inputs together, to match your selected video input with the corresponding audio input. When you change inputs on your TV to watch different video products, your TV will send signals via your remote control and the infrared emitters to your digital A/V receiver to change inputs. You will automatically hear the high quality digital surround sound from digital products like your DVD player, and high quality analog stereo or surround sound from non-digital products like your VCR. Additionally, all IR remote signals from your Mitsubishi remote or other manufacturers remote will be passed through your TV to your A/V devices. Your A/V devices can be hidden or behind cabinet doors and con trolled by pointing the remote at the TV. 14 Part II: Installation Special Setups: A/V Equipment (For System 4 Home Theater IR Control) VCR: Connect the cables to the TV as directed on page 17, with the following exception: Connect the audio output connection to the appropriate in...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :