Évaluations - 2, GPA: 3
(
)
)
|
Facilité d'utilisation
• Connect home antenna to Incoming Cable from Home Antenna ANT connection on back of television. Select TV mode in the SET UP menu. Note: Cable Mode is preset at the factory. Antenna users must change to TV Mode in the Set Up menu (page 19). Remote Control Battery Installation Requires two AA batteries (supplied). Battery Polarity AA/ 1.5A AA/ 1.5A 1 2 3 Procedure 1. Turn the remote control face down. Remove batterycover by pressing down on the marking on the coverand sliding it off in the direction indicated. 2. Install batteries matching (+) and (-) polarity signs. 3. Replace the battery cover by sliding in reverse until thelock snaps. Note: Incorrect installation can cause battery leakage and corrosion that will damage the Remote Control. Precautions • Replace batteries in pairs. • Do not mix battery types (zinc carbon with alkaline). • Do not recharge, heat, short-circuit, disassemble, or burn batteries. 4 • INITIAL SET UP MENU Initial Set Up Menu For your convenience, Auto Set up menu will be displayed on screen when the set is turned on for the first time. If needed, follow the menus and procedures for setting up the features. IDIOMA/LANGUE To change menu language to ENGLISH, SPANISH or FRENCH. Procedure • Press VOL • to select English, Spanish or French. FIRST PLEASE CONNECT THE ANTENNA INITIAL SET UP IDIOMA/LANGUE ENGLISH • MODE CABLE • AUTO PROGRAM • GEOMAGNETIC CORRECTION • TILT CORRECTION • PRESS ACTION TO EXIT MODE To select TV (antenna) or CABLE mode depending on the signal source. Procedure • Press VOL • to select TV or CABLE. FIRST PLEASE CONNECT THE ANTENNA INITIAL SET UP IDIOMA/LANGUE ENGLISH • MODE CABLE • AUTO PROGRAM • GEOMAGNETIC CORRECTION • TILT CORRECTION • PRESS ACTION TO EXIT AUTO PROGRAM To automatically program all channels with a signal. Procedure • Press VOL • to start Auto Programming. GEOMAGNETIC CORRECTION This feature is used to adjust discoloration of the picture due to the earth’s magnetic field in the area. Procedure • Press VOL .. to display adjustment menu. • Press • VOL or VOL .. to adjust discoloration in picture. FIRST PLEASE CONNECT THE ANTENNA INITIAL SET UP IDIOMA/LANGUE ENGLISH • MODE CABLE • AUTO PROGRAM • GEOMAGNETIC CORRECTION • TILT CORRECTION • PRESS ACTION TO EXIT GEOMAGNETIC CORRECTION - - - - - - - - -- - - - - - - - -0 ..TO ADJUST PRESS ACTION TO EXIT Note: Geomagnetic Correction is not available in model CT-27HL14. TILT CORRECTION This feature is used to adjust the tilt of the picture due to earth’s magnetic field in the area. Procedure • Press VOL .. to display adjustment menu. • Press • VOL or VOL .. to adjust picture tilt. FIRST PLEASE CONNECT THE ANTENNA INITIAL SET UP IDIOMA/LANGUE ENGLISH • MODE CABLE • AUTO PROGRAM • GEOMAGNETIC CORRECTION • TILT CORRECTION • PRESS ACTION TO EXIT TILT CORRECTION 0 ..TO ADJUST PRESS ACTION TO EXIT ENGLISH FIRST PLEASE CONNECT THE ANTENNA INITIAL SET UP IDIOMA/LANGUE ENGLISH • MODE CABLE • AUTO PROGRAM • GEOMAGNETIC CORRECTION • TILT CORRECTION • PRESS ACTION TO EXIT 5 • OPTIONAL EQUIPMENT CONNECTIONS Optional Equipment Connections Note: The remote control must be programmed with supplied codes to operate the optional equipment. VCR Connection Follow this diagram when connecting your television to a VCR only. Use either the Video or S-Video cable to hook up the VCR to VCR / S-VCR the video input. ENGLISHANT IN ANT OUT S-VIDEO COMPONENT VIDEO INPUT VIDEO 1 2 INPUT PROG OUT TO AUDIO AMP VIDEO Y PB PR L R AUDIO DIGITAL INPUT L R L R 1 2 3ANT PLAY STOP R E W FF AV IN AV OUT S-VIDEO VIDEO AUDIO L R L R OR Incoming Cable CABLES NOT INCLUDED TERMINALS ON BACK OF TELEVISION Note: Rear A/V jacks diagram may vary, depending on model. Please refer to the FEATURE CHART on page 3 for your model’s capabilities. Viewing a television program Procedure • Tune the television to the program you want to view. Viewing a video Procedure • Option A • Press the TV/VIDEO button and the numeric keys on the remote control to select the video input (VIDEO 1, VIDEO 2, etc.) connected to your VCR. • Begin the video. • Option B • Tune the television to Channel 3 or 4, depending on your VCR. • Begin the video. Recording a television program Procedure • Option A (Recording and viewing the same program). • Tune the television to Channel 3 or 4, depending on your VCR. • Using the VCR, tune to the television program you want to record. • Begin recording. • Option B (Recording one program while viewing another program) • Press the TV/VIDEO button and the numeric keys on the remote control to select the video input (VIDEO 1, VIDEO 2, etc.) connected to your VCR. • Using the VCR, tune to the television program you want to record. • Begin recording. • Press the TV/VIDEO button and the numeric keys on the remote control to switch back to TV mode. • Tune the television to the program you want to view. Cable Box Connection Follow this diagram when connecting your television to a cable box only. TERMINALS ON BACK OF TELEVISION CABLE BOX Incoming ANTANT I...
Ce manuel est également adapté pour les modèles :TV - CT27HL14 (3.33 mb)
TV - CT32HC14 (3.33 mb)
Récepteur et amplificateur - CT-32HXC14 (3.33 mb)
Récepteur et amplificateur - CT-32HC14 (3.33 mb)