Évaluations - 4, GPA: 4.5
(
)
)
|
Facilité d'utilisation
TO DO THIS... PRESS Turn on/off POWER Select a Channel 0~9 Change Channels Up/Down CH CH Back to previous channel R-TUNE Operating a DBS Program the remote control to use with DBS. TO DO THIS... PRESS Audio Track SAP Select a Channel 0~9 Program Information RECALL Back to previous channel R-TUNE Select next page up/down DVD/VCR CH Exit menus EXIT Display program Guide GUIDE Minor channel numbers PROG TO DO THIS... PRESS Turn on/off POWER Select ACTION CH Menu Navigation VOL VOL CH DVD Display RECALL Select Chapter 0~9 Display DVD menu MENU Skip Search Reverse REW Skip Search Fast Forward FF DVD Record REC Title R-TUNE PLAY Play • Open/Close TV/VCR Return EXIT Stop STOP Still PAUSE Chapter + / DVD/ VCR CH TO DO THIS... PRESS Turn on/off POWER Display DBS menu MENU Menu Navigation/ Change Channels Up/Down CH CH Menu Navigation VOL VOL 10 • REMOTE CONTROL OPERATION Programming The Remote Control The Universal Remote Control can be programmed to operate many manufacturers’ components, using the component function buttons for VCR, DVD, CABLE or DBS. Follow the procedures for programming your Remote Control with or without a code for the component. Device Operates Default TV TV (Panasonic Only) Panasonic Code VCR VCR (Preset) Panasonic Code DBS/CBL DBS STB & CBL STB (Preset) Panasonic DBS Code DVD DVD (Preset) Panasonic Code Note: Determine the manufacturer of the component and look in the table for the code (found on page 12). Procedure 1. Confirm that the external component is plugged in and operating. 2. Turn the component off. ACTION 3. Press and POWER together, for at least 5 seconds. After 5 seconds, the illuminated mode (component) buttons will begin to flash. Release the ACTION and POWER buttons. 4. Press appropriate component button on the Remote Control VCR, DVD, CABLE or DBS. The component button will illuminate steadily and all others will go out. 5. Enter the 3-digit component code using the Remote Control numeric keypad (0 ~ 9 buttons). The component button will blink twice. 6. Press the Remote Control POWER to test the component. If the procedure was successful, the component will turn on and the component key will blink twice and then go out. Note: If the component does not operate with the Remote Control, repeat steps 3 through 6 using another code (some brands have multiple codes). If an incorrect code is entered, or if the procedure takes longer than 30 seconds, the programming will fail. Programming Without A Code This procedure searches all codes and is called the “sequence method.” 1. Confirm that the external component is plugged in and on. 2. Turn the component off. ACTION 3. Press and POWER together, for at least 5 seconds. After 5 seconds, the illuminated mode (component) buttons will begin to flash. Release the ACTION and POWER buttons. 4. Press the appropriate component button on the Remote Control. The component button will illuminate steadily and all others will go out. 5. Press the POWER button to set the remote control into the step and set mode. 6. Point the remote control towards the component. 7. Press VOL • (the mode key will blink three times), then press the Remote Control POWER button to test the component. Continue this process until the proper code is found. If the procedure was successful, the component will turn on. Note: Each time you press the VOL .. button, make sure that the component key blinks twice before pressing the POWER button. ACTION 8. Once the device responds, press to store the code. The mode (component) button will blink twice. Note: It may take many attempts before the correct code is found. If you miss a code, press • VOL, then press the POWER button to test the component. Component Codes The Universal Remote Control is capable of operating many component brands after entering a code. Some components may not operate because the codes are not available due to limited memory. The Universal Remote Control does not control all features found in each model. Write the code numbers from tables in this space. This will serve as a reference if you need to programyour Remote Control. VCR CABLE DVD DBS ENGLISH 11 • REMOTE CONTROL OPERATION Component Codes (cont.) ENGLISH Codes For VCR Brand Code Admiral 335 Aiwa 332 Akai 314, 315, 316, 329 Audio Dynamic 311, 339 Bell & Howell 305, 313 Broksonic 320, 326 Canon 323, 325 CCE 343 Citizen 306 Craig 305, 306, 329 Curtis Mathes 324, 345 Daewoo 301, 324, 343 DBX 310, 311, 339 Dimensia 345 Emerson 303, 319, 320, 325, 326, 343 Fisher 305, 307, 308, 309, 313 Funai 320, 326, 334 GE 324, 333, 345 Goldstar 306 Gradiente 334 Hitachi 300, 323, 345 Instant Replay 323, 324 Jensen 339 JVC 310, 311, 334, 339 Kenwood 306, 310, 311, 339 LXI 300, 305, 306, 307, 308, 309 Magnavox 323, 324, 331 Marantz 310, 311, 339 Marta 306 Memorex 309, 324 MGA 338, 340, 341, 347, 348 Minolta 300, 345 Mitsubishi 338, 340, 341, 347, 348 Multitech 304, 347 NEC 310,311, 334, 339 Olympic 323, 324 Optimus 306, 321, 328, 335 Orion 320, 326 Panasonic 321,322, ...
Ce manuel est également adapté pour les modèles :TV - CT32HC14 (3.33 mb)
TV - CT32HXC14 (3.33 mb)