Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
SET UP for Input Signals SIGNAL menu Note: “SIGNAL” setup menu displays a different setting condition for each input signal. 1 2 2 Press to display the SET UP menu. Press to select the “SIGNAL”. For VIDEO (S VIDEO) For RGB 3 3 Press to display the SIGNAL menu. Press to select the menu to adjust. Press to adjust the menu. For COMPONENT For Digital 1/2 SIGNAL SCREENSAVER PC OFF STANDBY SAVE OFF POWER MANAGEMENT OFF AUTO POWER OFF OFF OSD LANGUAGE ENGLISH (US) COMPONENT/RGB-IN SELECT RGB INPUT LABEL POWER SAVE SET UP 3D Y/C FILTER (NTSC) COLOR SYSTEM SIGNAL ON AUTO 3 : 2 PULLDOWN Panasonic AUTO (4 : 3) OFF 4:3 [ VIDEO ] NOISE REDUCTION OFF REFRESH RATE 100 Hz SYNC SIGNAL H-FREQ. V-FREQ. kHz Hz 63.98 60.02 SIGNAL FORMAT 1280.1024/60 [ RGB ] 3 : 2 PULLDOWN XGA MODE NOISE REDUCTION OFF REFRESH RATE 100 Hz AUTO OFF 1024 . 768 Press to exit from adjust mode. 3 : 2 PULLDOWN SIGNAL OFF [ Digital ] NOISE REDUCTION OFF REFRESH RATE 100 Hz H-FREQ. V-FREQ. kHz Hz 63.98 60.02 SIGNAL FORMAT 1280.1024/60 3 : 2 PULLDOWN SIGNAL OFF [ COMPONENT ] XGA MODE 1024 . 768 NOISE REDUCTION OFF REFRESH RATE 100 Hz H-FREQ. V-FREQ. kHz Hz 63.98 60.02 SIGNAL FORMAT 1280.1024/60 3D Y/C FILTER – For NTSC AV images Select “SIGNAL” from the “SET UP” menu during VIDEO (S VIDEO) input signal mode. (“SIGNAL [VIDEO]” menu is displayed.) Press to select the “3D Y/C FILTER (NTSC)”. 3D Y/C FILTER (NTSC) ON Press to set ON / OFF. Note: When ON, this setting only affects NTSC input signals. SET UP for Input Signals COLOR SYSTEM / Panasonic AUTO Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input signal mode.(“SIGNAL [VIDEO]” menu is displayed.) Press to select the “COLOR SYSTEM” or “Panasonic AUTO”. Press to select each function. If the image becomes unstable: With the system set on Auto, under conditions of low level or noisy input signals the image may in rare cases become unstable. Should this occur, set the system to match the format of the input signal. 3D Y/C FILTER (NTSC) COLOR SYSTEM SIGNAL ON AUTO 3 : 2 PULLDOWN Panasonic AUTO (4 : 3) OFF 4:3 [ VIDEO ] Mode Function COLOR SYSTEM Set the color system to match the input signal. When selecting “AUTO”, the color system is automatically selected from NTSC/PAL/SECAM, however, M.NTSC signal is not displayed properly depending on the attached terminal board. To display M.NTSC signal, select “M.NTSC” in COLOR SYSTEM. AUTO SECAM M.NTSC NTSCPAL Panasonic AUTO (4 : 3 ) Set to “4:3” to view 4:3 images in an unchanged format when Panasonic AUTO is selected. If you would like to view 4:3 images in Just format, set to “JUST”. Note: Panasonic AUTO does not function when BNC Dual Video Terminal Board (TY-FB9BD) is used. 3:2 PULLDOWN 3:2 PULLDOWN: When ON, the display attempts to reproduce a more natural interpretation of sources such as movie pictures, which are recorded at 24 frames per second. If the picture is not stable, turn the setting to OFF. Notes: When ON, this setting only affects the following signal input: • NTSC / PAL signal input during “VIDEO (S VIDEO)” input signal. • 525i(480i), 625i(575i), 1125(1080)/60i signal input during “COMPONENT” input signal. Press to select “3:2 PULLDOWN”. 3 : 2 PULLDOWN OFF Press to set ON/OFF. XGA MODE This menu is displayed when the input signal is Analogue (Component/PC). It allows switching between different XGA signal settings for fi eld angle/sampling. Press to select “XGA MODE”. Press to select “1024.768”, “1280.768” , XGA MODE 1024 . 768 “1366.768”. SET UP for Input Signals REFRESH RATE This function sets the refresh rate of the display. This menu is displayed when the input signal is 50 Hz system (50i, 50p, 25p, 24p, 24sF) of vertical scan rate. 100 Hz: Reduce screen fl icker. 50 Hz: Enhance the resolution of moving images. Note: It is recommended to set to 100 Hz normally. q REFRESH RATE 100 Hz Press to select REFRESH RATE. Press to adjust. NOISE REDUCTION Sets the following three NR (Noise Reduction) functions together. VIDEO NR, MOSQUITO NR, BLOCK NR () Press to select “NOISE REDUCTION”. NOISE REDUCTION OFF Press to select “OFF”, “MIN”, “MID”, “MAX”, “ADVANCED”. Advanced NR Sets the three NR functions separately. Press to select “ADVANCED”. Press to enter ADVANCED NR. Press to select VIDEO NR, MOSQUITO NR or BLOCK NR. Press to select “OFF”, “MIN”, “MID”, “MAX”. () NOISE REDUCTION ADVANCED Ў ADVANCED NR [ VIDEO ] MOSQUITO NR VIDEO NR BLOCK NR OFF OFF OFF ADVANCED NR [ Digital ] MOSQUITO NR VIDEO NR BLOCK NR OFF OFF OFF ADVANCED NR [ COMPONENT ] MOSQUITO NR VIDEO NR BLOCK NR OFF OFF OFF ADVANCED NR [ RGB ] MOSQUITO NR VIDEO NR BLOCK NR OFF OFF OFF VIDEO NR: Automatically reduces unwanted picture noise. MOSQUITO NR: Reduces mosquito noise around subtitles on MPEG videos. BLOCK NR: Reduces block noise when playing MPEG videos. Notes: • NOISE REDUCTION cannot be adjusted while a PC signal is being applied. • BLOCK NR cannot be adjusted while a HD signal is being applied. SET UP for Input Signals SYNC Select SIGNAL from the “SET UP” menu during RG...
Ce manuel est également adapté pour les modèles :TV - TH-37PR11UK (3.76 mb)
TV - TH-37PR11UH (3.76 mb)
TV - TH-42PR11UK (3.76 mb)