Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
STANDBY AFTER SCR SAVER: Operates while SCREENSAVER DURATION, and display enters standby mode. ON : Operates when START is selected and the ACTION ( ) button is pressed. START setting 4 When the MODE is set to ON, press to select START. Press to start SCREENSAVER. The menu screen will disappear and the SCREENSAVER will be activated. To stop the SCREENSAVER under ON, press the R button or any buttons on the main unit. Note: When the display is turned off, the SCREENSAVER will be deactivated. SCREENSAVER (For preventing image retention) Setup of SCREENSAVER Time After selecting TIME OF DAY, INTERVAL or STANDBYAFTER SCR SAVER, the relevant Time Setup will become available for selection and the Operating Time may be set. (Time cannot be set when “MODE” is “ON” or “OFF”.) Press to select START TIME / FINISH TIME (When TIME OF DAY is selected). Press to select SHOW DURATION / SAVER DURATION (When INTERVAL is selected). Press to select SCREENSAVER DURATION (When STANDBY AFTER SCR SAVER is selected). Press to setup. button: Forward button: Back Notes: • Pressing “ ” or “ ” button once changes the Time 1 minute. [However, switching occurs every 15 minutes when Periodic Time is selected.] • Pressing “ ” or “ ” button continuously changes the Time by 15 minutes. • “SCREENSAVER DURATION” of the “STANDBY AFTER SCR SAVER” can be set from 0:00 to 23:59. When this is set to “0:00”, “STANDBY AFTER SCR SAVER” will not be activated. SCREENSAVER START MODE FINISH TIME START TIME TIME OF DAY 6 : 15 12 : 30 PRESENT TIME OF DAY MON 15 : 00 SCREENSAVER START MODE SAVER DURATION INTERVAL SHOW DURATION 12 : 00 3 : 00 PRESENT TIME OF DAY MON 15 : 00 SCREENSAVER START MODE SCREENSAVER DURATION STANDBY AFTER SCR SAVER 6 : 15 PRESENT TIME OF DAY MON 15 : 00 Note: Timer function will not work unless “PRESENT TIME OF DAY” is set. WOBBLING Automatically shifts the display image (therefore unnoticeable to the eye) to prevent image retention of sharper contour of image. 1 Press to display the SET UP menu. 2 2 Press to select “WOBBLING”. Press to select “ON” or “OFF”. ON: Shifts the position of the display image on a fi xed time interval. 3 Press to exit from adjust mode. 1/2 SIGNAL INPUT LABEL WOBBLING SET UP POWER MANAGEMENT OFF OFF AUTO POWER OFF OFF STANDBY SAVE OFF(SERIAL) ECO OFF OSD LANGUAGE ENGLISH (US) COMPONENT/RGB-IN SELECT RGB SCREENSAVER Notes: • If “MULTI DISPLAY SETUP” is set to “ON”, this function does not operate. • When this function is operating, part of the screen may appear to be missing. Reduces power consumption • POWER MANAGEMENT: When this function is set to ON, it operates under the following conditions to turn the power on or off automatically. When no pictures are detected for 30 or so seconds during PC signal input: >Power is turned off (standby); the power indicator lights up orange. When pictures are subsequently detected: >Power is turned on; the power indicator lights up green. Notes: • This function operates only during input from PC IN terminal. • This function is effective when “SYNC” is set to “AUTO” and during normal viewing (one picture screen). • AUTO POWER OFF: Equipment power supply is turned OFF when there is no signal. When this is set to ON, the power supply of the unit goes Off 10 minutes after the input signals stop. Note: This function is effective during normal viewing (one picture screen). • STANDBY SAVE: When this function is set to “ON”, serial communication is disabled during standby mode, reducing the power consumption during standby. To perform serial communication while in standby, set this function to “OFF(SERIAL)”. However, the standby power consumption is greater than when it is set to “ON”. • ECO: This function adjusts the brightness of the backlight to reduce power consumption. OFF: This function does not operate. ON: Backlight brightness is reduced. SENSOR: The backlight brightness is automatically adjusted according to the viewing environment. Note: When this function is set to “ON” or “SENSOR”, the “BACKLIGHT” setting in the PICTURE menu is disabled. Press to select the menu to adjust. Press to select “ON” or “OFF”. On Off 1 2 1/2 SIGNAL INPUT LABEL WOBBLING SET UP OFFPOWER MANAGEMENT OFF AUTO POWER OFF OFF STANDBY SAVE OFF(SERIAL) ECO OFF OSD LANGUAGE ENGLISH (US) COMPONENT/RGB-IN SELECT RGB OFF SCREENSAVER Press to exit from SET UP. Customizing the Input labels This function can change the label of the Input signal to be displayed. (see page 16) 1 Press to display the SETUP menu. Press to select INPUT LABEL. 2 Press to display the INPUT LABEL screen. Press to select image input. 3 Press to change input label. 1/2 SIGNAL SCREEN SAVER INPUT LABEL WOBBLING POWER MANAGEMENT OFF AUTO POWER OFF OFF ECO OFF OSD LANGUAGE ENGLISH (US) COMPONENT/RGB-IN SELECT RGB OFF SET UP STANDBY SAVE OFF(SERIAL) VIDEO Component INPUT LABEL PC DVI HDMI1 HDMI2 VIDEO Component PC DVI HDMI1 HDMI2 Image input Input label [VIDEO] VIDEO / DVD1 / DVD2 / DVD3 / Blu-ray1 / Blu-ray2 / Blu-ray3 / CATV / VCR / STB...