Évaluations - , GPA: ( )

Instructions Panasonic, Modèle TH-42PX20

Fabricant : Panasonic
Taille : 1.12 mb
Nom Fichier : TH42PX20U.PDF

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

(.1. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. .2. EIA/CEA-861/861B profiles compliance covers profiles for transmission of uncompressed digital videoincluding high bandwidth digital content protection. .3. Consult your consumer electronics dealer for availability details. .4. (HDMI IN)Please refer to page 24. • The HDMI terminal of this equipment is TYPE A. Cable Connection PC Input Terminals connection Notes: (1) Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. , the image will not be displayed properly if the signals exceed 1,200 lines.) (2) The display resolution is a maximum of 768 768 dots (TH-42PX20), 1,024 . 768 dots (TH-50PX20) when the aspect mode is set to “ ” 768 dots (TH-42PX20), 1,366 . 768 dots (TH-50PX20) when the aspect mode is set to “ ”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with suf (3) Some PC models cannot be connected to the set. (4) There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal. (5) The computer shown in the illustration is for example purposes only. (6) Additional equipment and cables shown are not supplied with this set. (7) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. S-VIDEO PCVIDEO INPUT 3 L AUDIO R COMPUTER Conversion adapter (if necessary) RGB D-sub 15p Stereo plug PC cable Connect a cable which matches the audio output terminal on the computer. Less than 4" (10 cm) Ferrite core (small size) (supplied) Ferrite core (large size) (supplied) Audio Less than 4" (10 cm) Less than 4" (10 cm) 1 678 3 9 45 10 1514131211 2 Signal Names for D-sub 15P Connector Pin No. 1 2 3 4 5 Pin No. 6 7 8 9 10 Pin No. 11 12 13 14 15 Signal Name R G B NC (not connected) GND (Ground) Signal Name GND (Ground) GND (Ground) GND (Ground) NC (not connected) GND (Ground) Signal Name NC (not connected) NC HD/SYNC VD NC Pin Layout for PC Input Terminal Power ON / OFF AC cord connection Connecting the AC cord plug to the Plasma TV. Ferrite core (large size) (supplied) Fix the AC cord plug securely to the Plasma TV with the clamper. How to Turn the Power On POWER Power indicater Connecting the Plug to the Wall Outlet Note: The TV’s power cord must first be plugged into the wall outlet and then turned on at the POWER switch (standby mode). Press the POWER switch on the TV to turn the set on. POWER-ON: Red When the set is on press the POWER switch on the TV to turn the set off. STANDBY: No light Example: The screen below is displayed for a while after the TV is turned on. (setting condition is an example.) CH 3 JUST SAP VIVID Press the POWER button on the remote control to turn the TV on: Red Press the POWER button on the remote control to turn the TV off: No light (standby) ACTION TV DTV CBL AUXDVDVCR DBS RCVR CH CH VOL VOL RECALL SAP PC MENU MUTE PECT TV/VIDEO LIGHT POWER Remote Control senser POWER Note: The TV will still consume some power as long as the power cord is still inserted into the wall outlet. Menu Language Selection In SET UP Menu, Select IDIOMA/LANGUE to change menu language to ENGLISH, ESPANOL (Spanish) or FRANCAIS (French). (refer to page 26) VHF, UHF and Cable TV VHF and UHF PC CARD EJECT SD CARD PUSH-EJECT HPJACTION INPUT VOLUME CHANNEL S-VIDEO PCVIDEO INPUT 3 L AUDIO R HPJ PC CARD EJECT SD CARD PUSH-EJECT ACTION INPUT VOLUME CHANNEL S-VIDEO PCVIDEO INPUT 3 L AUDIO R Press to turn the TV on (See page 19). Press TV to operate the TV set with the remote control. Press to select the desired channel. Select the desired volume level. Notes: (1) The channel number and volume level remain the same even after the TV is turned off. (2) Power consumption and howling sound can be reduced if the volume level is lowered. 1 2 3 4 Power switch Remote control sensor Operation can be done from the TV set. • Channel selectors • Volume adjusters TV POWER ACTION CH CH VOL VOL ACTION CH CH VOL VOL 1 2 3 4 5 6 7 8 0 9 DTV AUXDVDVCR DBS RCVR RECALL PC MENU R-TUNE PROG GUIDE SAP PAGE EXIT PIP SPLIT MOVE SWAP STOP PAUSE REC PIP MAX FF PIP MIN REW FREEZE TV/VCR PIP CH VCR CH SEARCH OPEN/CLOSE MUTE PECT TV/VIDEO LIGHT POWER CBL CH CH VOL VOL ACTION TV PLAY ACTION button (Press to make selections.) INPUT button (Change to input signal.) C.A.T.S sensor Plasma C.A.T.S (Contrast Automatic Tracking System) Plasma C.A.T.S automatically senses the ambient light conditions and adjusts the brightness and gradation accordingly, to optimise contrast. (Effective when Picture mode is set to Auto.) Power indicator VHF, UHF and Cable TV Cable TV When the antenna cable is connected to the TV antenna terminal via a cable box or VCR, set the TV channel to CH3 or CH4. This does not apply when signal is input from VIDEO INPUT. Ferrite core (large size) (supplie...