Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner. Observe the following precautions: 1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. 2. Do not combine a used battery with a new one. 3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”). 4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 5. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. 6. Do not burn or breakup batteries. Batteries must not be exposed to excessive heat such as sunshine, fire or the like. 8 1 2 Plug the AC cord into the display unit. Plug the AC cord until it clicks. Note: Make sure that the AC cord is locked on both the left and right sides. Connections When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. AC cord fi xing Unplug the AC cord Unplug the AC cord pressing the two knobs. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet fi rst. Using the clamper Secure any excess cables with clamper as required. AC cord connection and fi xing, cable fi xing Speaker connection Speakers (Optional accessories) Red Black While pressing the lever, insert the core wire. Return the lever. Red Black TH-58PF20U TH-65PF20U 1 2 Keep pushing both side snaps hooks Set the tip in the hooks Keep pushing the knob knob Insert the clamper in a hole. Attach the clamper To remove from the unit: hole Bundle the cables snaps To loosen: 9 VIDEO and COMPONENT / RGB IN connection Y, P B, P R , OUT PR P B Y AUDIO R OUT L VIDEO OUT AUDIO R OUT L Notes: • Change the “COMPONENT/RGB-IN select” setting in the “SETUP” menu to “COMPONENT” (when COMPONENT signal connection) or “RGB” (when RGB signal connection). • Accepts only RGB signals with “SYNC ON G”. RCA-BNC Adapter plug RCA-BNC Adapter plug DVD Player VCR Computer RGB Camcorder Connections Video equipment connection SLOT: Terminal board (optional accessories) insert slot (see page 5) Note: The right side slot is for terminal board with 2-slot width. The terminal board with 1-slot width does not function when installed in the right side slot. Note: Additional equipment, cables and adapter plugs shown are not supplied with this set. PC IN: PC Input Terminal Connect to video terminal of PC or equipment with Y, PB(CB) and PR(CR) output. (see page 11) SERIAL: Control the Plasma Display by connecting to PC. (see page 12) Ex. TH-65PF20U AV IN (VIDEO): Composite Video Input Terminal (see below) COMPONENT/RGB IN: Component/RGB Video Input Terminal (see below) AV IN (HDMI): HDMI Input Terminal (see page 10) DVI-D IN: DVI-D Input Terminal (see page 10) Connect to video equipment such as VCR or DVD player. LAN: Connect to a network to control the unit. (see page 20) Connections HDMI connection [Pin assignments and signal names] HDMI cable Pin No. Signal Name Pin No. 11 12 Signal Name T.M.D.S Clock Shield T.M.D.S Clock1 2 T.M.D.S Data2+ T.M.D.S Data2 Shield 3 T.M.D.S Data213 CEC 4 5 6 7 8 9 10 T.M.D.S Data1+ T.M.D.S Data1 Shield T.M.D.S Data1T. M.D.S Data0+ T.M.D.S Data0 Shield T.M.D.S Data0T. M.D.S Clock+ 14 15 16 17 18 19 Reserved (N.C. on device) SCL SDA DDC/CECGround +5V Power Hot Plug Detect 19 3 1 18 4 2 HDMI AV OUT DVD player Note: Additional equipment and HDMI cable shown are not supplied with this set. DVI-D IN connection PC with DVI-D video out DVI-D Input Connector Pin Layouts 9 Connection port view 81 17 24 Notes: Stereo mini plug (M3) DVI-video cable (Within 5 m) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 Signal Name T.M.D.S. data 2T. M.D.S. data 2+ T.M.D.S. data 2 shield DDC clock DDC data T.M.D.S. data 1T. M.D.S. data 1+ T.M.D.S. data 1 shield Pin No. 13 14 15 16 17 18 19 20 21 22 23 24 Signal Name +5 V DC Ground Hot plug detect T.M.D.S. data 0T. M.D.S. data 0+ T.M.D.S. data 0 shield T.M.D.S. clock shield T.M.D.S. clock+ T.M.D.S. clock16 • Additional equipment and cables shown are not supplied with this set. • Use the DVI-D cable complying with the DVI standard. Image deterioration may occur depending on the length or the quality of the cable. Conversion adapter (if necessary) Mini D-sub 15p RGB PC cable Audio Stereo mini plug (M3) Connect a cable which matches the audio output terminal on the computer. (Male) (Female) COMPUTER 11 PC Input Terminals connection Notes: • With regard to the typical PC input signals that are described in the applicable input signals list, adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list. • Computer signals which can be input are those with a horizontal scanning frequency of ...
Ce manuel est également adapté pour les modèles :TV - TH-58PF20U (5.33 mb)