Évaluations - 1, GPA: 5
(
)
)
|
Photos et spécifications Sony KDL-26S4000 |
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
21 Features menu................................................................................................................ 22 Set-up menu.................................................................................................................... 23 Digital Set-up menu ............................................................................................... 26 Additional Information Specifications..................................................................................................................28 Troubleshooting .............................................................................................................. 30 : for digital channels only Before operating the TV, please read the “Safety information” section of this manual. Retain this manual for future reference. 3 GB Start-up Guide 1: Checking the accessories Remote RM-ED009 (1) Size AA batteries (R6 type) (2) Stand (1) Screws for stand (3) To insert batteries into the remote Push and lift the cover to open. 2: Attaching the stand 1 Open the carton box and take out the stand and the screws. 2 Place the TV set on the stand. Take care not to interfere with cables. 3 Fix the stand to the TV using the supplied screws. ~ If using an electric screwdriver, set the tightening torque at approximately 1.5 N·m (15 kgf·cm) 4 GB 5 GB Start-up Guide 3: Connecting an aerial/ VCR/ DVD recorder 4: Preventing the TV from toppling over 1 Install a wood screw (4 mm in diameter, not supplied) in the TV stand. 2 Install a machine screw (M6 x 12, not supplied) into the screw hole of the TV. 3 Tie the wood screw and the machine screw with a strong cord. 5: Bundling the cables Connecting an aerial/cable Connecting an aerial/ cable/ VCR/ DVD recorder Coaxial cable Scart lead VCR/ DVD recorder Coaxial cable Coaxial cable Terrestrial signal or cable Terrestrial signal or cable 6: Selecting the language, country/region and location 3,4,5 1 Connect the TV to your mains socket (220-240V AC, 50Hz). 2 Press 1 on the TV. When you switch on the TV for the first time, the Language menu appears on the screen. 3 Press F/f to select the language displayed on the menu screens, then press . Auto Start Up Language Country Location Select: Confirm: 4 Press F/f to select the country/region in which you will operate the TV, then press . Auto Start Up Language Country Location Back: Select: Confirm: If the country/region in which you want to use the TV does not appear in the list, select “-” instead of a country/region. 5 Press F/f to select the location type in which you will operate the TV, then press . ~ Sony recommends you to select “Home” for power saving. Auto Start Up Language Country Location Home Shop Back: Select: Confirm: This option selects the initial picture mode appropiate for the typical lighting condition in these enviroments. 7: Auto-tuning the TV 1 Press . Back: Start: Cancel: MENU Do you want to start automatic tuning? 2 Press F/f to select “Antenna” or “Cable”, then press . If you select “Cable”, the screen for selecting the scan type appears. See “To tune the TV for Cable connection” (page 7). The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, so do not press any buttons on the TV or remote while proceeding. 6 GB If a message appears for you to confirm the aerial connection Detaching the Table- No digital or analogue channels were found. Check all the aerial/cable connection and then press to start auto-tuning again. Top Stand from the TV 3 When the Programme Sorting menu appears on the screen, follow the steps of “Programme Sorting” (page 23) If you do not change the order in which the analogue channels are stored on the TV, go to step 4. 4 Press MENU to exit. The TV has now tuned in all the available channels. ~ When a digital broadcast channel cannot be received, or when selecting a region in which there are no digital broadcasts the time must be set after performing step 3. To tune the TV for Cable connection 1 Press . 2 Press F/f to select “Scan Type”, then press g to select “Quick Scan” or “Full Scan”, then press . "Quick Scan" : channels are tuned according to the cable operator information within the broadcast signal. Recommended setting for "Frequency", "Network ID" and "Symbol Rate" is "Auto". This option is recommended for fast tuning when supported by your cable operator. If the "Quick Scan" does not tune, please use the "Full Scan" method below. "Full Scan" : All available channels are tuned and stored. This procedure may take some time. This option is recommended when "Quick Scan" is not supported by your cable provider. For further information about supported cable providers, refer to support web site: 3 Press G/g/f to select “Start”. The TV starts searching for channels. Do not press any buttons on the TV or remote. ~ Some cable providers do not support “Quick Scan”. If no channels are detected using “...
Ce manuel est également adapté pour les modèles :TV - KDL-37S4000 (5.96 mb)
TV - KDL-32S4000 (5.96 mb)
TV - KDL-26U4000 (5.96 mb)
TV - KDL-37U4000 (5.96 mb)