(Refer to page 38.) Rear panel PC 1 2 3 4 5 6 7 8 10 11 12 13 14 15 PC IN Red (R) Green (G) Blue (B) Grounding Grounding (DDC) Red (R) Grounding Green (G) Grounding Blue (B) Grounding Reserved Sync Grounding Grounding Data (DDC) Horizontal sync. Vertical sync. Clock (DDC) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PC OUT Red (R) Green (G) Blue (B) Grounding Grounding (DDC) Red (R) Grounding Green (G) Grounding Blue (B) Grounding Reserved Sync Grounding Grounding Data (DDC) Horizontal sync. Vertical sync. Clock (DDC) Pin Configuration 15Pin Signal Cable (based on protruded pin) Setting up Your Display Plug and Play ENG Our adoption of the new VESA® Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification data (EDID) using Display Data Channel (DDC) protocols. Preset Signals Source Video Vertical frequency (Hz) Horizontal frequency (kHz) Resolution (Lines) AV1(Video) AV1(S-Video) NTSC3.58 60 15.704 483 PAL 50 15.625 575 SECAM 50 15.625 575 NTSC4.43 60 15.734 483 PAL-M 60 15.734 483 PAL-N 50 15.625 575 Component 1 480/60i 60 15.734 483 576/50i 50 15.625 575 Component 2 480/60p 60 31.469 483 576/50p 50 31.250 575 720/60p 60 45.000 720 1080/50i 50 28.125 1080 1080/60i 60 33.750 1080 . When the 576/50p signal is received, the picture might be displayed abnormally or shift, depending on the receiver or A/V component. In that case, you can try “Chaning the Screen Position” on page 39. (But the screen position might be unmatched depending on the component.) 34 Setting up Your PC Software (Windows only) ENG The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. On the windows screen, select in the following sequence: Start Settings Control Panel. . . When the control panel screen appears, click on “Display” and a display dialog-box will appear. Select the “Settings” tab in the display dialog-box. The two key variables that apply the PDP-PC interface are “Resolution” and “Colors”. The correct settings for these two variables are: . Size (sometimes called “Resolution”) 1024 x 768 pixels. . Color “24-bit” color (might also be expressed as “16 million colors”) Shown at left is a typical screen for “Display” dialog box. If a vertical-frequency option exists on your display settings dialog box, the correct value is “60” or “60Hz”. Otherwise, just click “OK” and exit the dialog box. 35 PC Input Mode (42”) ENG Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: Standard Dot x Line Vertical frequency (Hz) Horizontal frequency (kHz) Vertical polarity Horizontal polarity VGA 640 x 480 85.0 43.3 N N 75.0 37.5 N N 72.8 37.9 N N 59.9 31.5 N N 720 x 400 70.1 31.5 P N SVGA 800 x 600 85.1 53.7 P P 75.0 46.9 P P 72.2 48.1 P P 60.3 37.9 P P 56.3 35.2 P P XGA 1024 x 768 85.0 68.7 P P 75.0 60.0 P P 70.1 56.5 N N 60.0 48.3 N N (N: Negative / P: Positive) . The interlace mode is not supported. . The PDP might operate abnormally if a non-standard video format is selected. . The 4:3 mode does not work with input signals from “720 x 400”. Notes . The text quality of PC screen is optimum in the VGA mode (640 x 480), the full size displayed PC mode is optimum in the SVGA mode (800 x 600). . When this PDP is used as a PC display, 24-bit color is supported (over 16 million colors). . Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows). Check your PC instruction book for information about connecting your PC to a PDP. . If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHz (horizontal). In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the Source button to enter the Video mode. Also, make sure that the PC is connected. . When connecting a notebook PC to the PDP, make sure that the PC screen is displayed through only the PDP monitor (Otherwise, random signals might appear). . When horizontal synchronous signals seem irregular in PC mode, check PC power saving mode or cable connections. 36 PC Input Mode (50”) ENG Standard Dot x Line Vertical frequency (Hz) Horizontal frequency (kHz) Vertical polarity Horizontal polarity VGA 640 x 350 70.086 31.469 N P 85.080 37.861 N P 640 x 400 85.080 37.861 P N 720 x 400 70.087 31.469 P N 85.039 37.927 P N 640 x 480 59.940 31.469 N N 72.809 37.861 N N 75.000 37.500 N N 85.008 43.269 N N W-VGA 848 x 480 60.000 29.838 P N 72.000 35.156 P N 75.000 36.072 P ...

Ce manuel est également adapté pour les modèles :
TV - PPM42P2S (4.62 mb)
TV - PS-42P2ST (4.62 mb)
TV - PS-42P2STR (4.62 mb)
TV - PS-50P2HT (4.62 mb)